Panasonic fp2/fp2sh - Page 292

11-24
FP2/FP2SH/FP10SH
Address
Name
Description
R9060
MEWNET-W/
-P
PC link
transmission
assurance
relay [for PC
link 0 (W/P)]
(*Note)
Unit
No.1
Turns on when Unit No. 1 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9061
Unit
No.2
Turns on when Unit No. 2 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9062
Unit
No.3
Turns on when Unit No. 3 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9063
Unit
No.4
Turns on when Unit No. 4 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9064
Unit
No.5
Turns on when Unit No. 5 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9065
Unit
No.6
Turns on when Unit No. 6 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9066
Unit
No.7
Turns on when Unit No. 7 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9067
Unit
No.8
Turns on when Unit No. 8 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9068
Unit
No.9
Turns on when Unit No. 9 is communicating properly in the PC
link mode. Turns off when operation is stopped, when an error
occurs, or when not in the PC link mode.
R9069
Unit
No.10
Turns on when Unit No. 10 is communicating properly in the
PC link mode. Turns off when operation is stopped, when an
error occurs, or when not in the PC link mode.
R906A
Unit
No.11
Turns on when Unit No. 11 is communicating properly in the
PC link mode. Turns off when operation is stopped, when an
error occurs, or when not in the PC link mode.
R906B
Unit
No.12
Turns on when Unit No. 12 is communicating properly in the
PC link mode. Turns off when operation is stopped, when an
error occurs, or when not in the PC link mode.
R906C
Unit
No.13
Turns on when Unit No. 13 is communicating properly in the
PC link mode. Turns off when operation is stopped, when an
error occurs, or when not in the PC link mode.
R906D
Unit
No.14
Turns on when Unit No. 14 is communicating properly in the
PC link mode. Turns off when operation is stopped, when an
error occurs, or when not in the PC link mode.
R906E
Unit
No.15
Turns on when Unit No. 15 is communicating properly in the
PC link mode. Turns off when operation is stopped, when an
error occurs, or when not in the PC link mode.
R906F
Unit
No.16
Turns on when Unit No. 16 is communicating properly I n the
PC link mode. Turns off when operation is stopped, when an
error occurs, or when not in the PC link mode.
Note) When the system registers 46=K0, PC link 0 for the link unit with a smaller slot No. and PC link 1
for one with a larger slot No.
When the system registers 46=K1, PC link 1 for the link unit with a smaller slot No. and PC link 0
for one with a larger slot No.