RFL Electronics IMUX 2000 - Page 10

Because RFL™ and Hubbell® have a policy of continuous product improvement, we reserve the right to change designs and specifications without notice.
M-DACS-T1 RFL Electronics Inc.
January 1, 2013 x (973) 334-3100
Figure 5-1. Typical desktop showing the RFL NMS version 10.3 icon...............................................................................5-3
Fig
ure 5-2. PC directly connected to a node using an RS-232 cable or an RJ-45 Ethernet cable ........................................5-5
Fi
gure 5-3. PC connected to a node from a rem
ote location ................................................................................................5-6
Figure 5-4. Construction of a typical RS-232 cable between the PC and an MA-235 .........................................................5-6
Fi
gure 5-5. PC at a remote location connected to 4 nodes, where each node is a different network....................................5-7
Fi
gure 5-6. PC at a remote location connected to 4 nodes, where all nodes are in the same network..................................5-8
Fi
gure 5-7. Typical networks and communications paths....................................................................................................5-9
Fi
gure 5-8. Network Management Software Main Window..............................................................................................5-10
Fi
gure 5-9. Basic drawing of the network used in the example .........................................................................................5-14
Figure 5-10. IMUX 2000 M-DACS Network Example.....................................................................................................
5-15
Fig
ure 5-11. Network Management Software Main window.............................................................................................5-17
Fig
ure 5-12. Edit Network Information Window...............................................................................................................5-18
Fi
gure 5-13. Read Network Setup Window .......................................................................................................................5-21
Fig
ure 5-14. Auto-Configure Options Window .................................................................................................................5-22
Fi
gure 5-15. Network View Window.................................................................................................................................5-
23
Figure 5-16. Display/Change Node window for node 1.....................................................................................................5-24
Fig
ure 5-17. DACS Module Configuration Window .........................................................................................................5-25
Fig
ure 5-18. Point-to-point system timing setting...............................................................................................................5-29
Fi
gure 5-19. M-DACS Drop/insert Linear system timing setting.......................................................................................5-30
Fig
ure 5-20. M-DACS Ring system timing setting.............................................................................................................5-31
Fi
gure 5-21. Port 1 Configuration parameters window for a T1 system ............................................................................5-32
Fi
gure 5-22. DACS module Map window for Node 1 of a T1 system...............................................................................5-35
Fi
gure 5-23. Typical FDL signal routing for map 0...........................................................................................................5-36
Fi
gure 5-24. Map Select Criteria window for Map 1 of a T1 or E1 system.......................................................................5-37
Fi
gure 5-25. DACS DS0 Map 0 window for a T1 system..................................................................................................5-40
Fig
ure 5-26. Robbed Bit Signal Selects window for T1 systems only...............................................................................5-42
Fi
gure 5-27. DACS Module Status window........................................................................................................................5-43
Fig
ure 5-28. Alert/Alarm Details window...........................................................................................................................5-45
Fi
gure 5-29. CM4 Configuration And Status Window ......................................................................................................5-46
Fig
ure 5-30. Configuration and Status window for the VF5C ...........................................................................................5-47
Fig
ure 5-31. View or Change a Card window for the VF16B............................................................................................5-48
Fig
ure 5-32. Configuration and Status window for the DS562I.........................................................................................5-49
Fig
ure 5-33. Network View window after connecting lines to nodes .................................................................................5-50
Fi
gure 5-34. Typical Alarm Log report..............................................................................................................................5-52
Fi
gure 5-35. Page 1 of typical Complete Network Information Report.............................................................................5-53
Fi
gure 5-36. Typical Connection View Report ..................................................................................................................5-54
Fi
gure 5-37. Page 1 of a typical DACS Map Report..........................................................................................................5-55
Fi
gure 5-38. Page 1 of a Typical DACS MapDifference Report........................................................................................5-56
Figu
re 5-39. Typical Difference Report.............................................................................................................................5-57
Fi
gure 5-40. Page 1 of a typical Event Log Report............................................................................................................5-58
Fi
gure 5-41. Typical Network Diagram Report .................................................................................................................5-59
Figure 6-1. L
ocal connection...............................................................................................................................
.................6-
2
Figure 6-2. Remote connection over a dial-up circuit..........................................................................................................6-2
Fi
gure 6-3. Remote connection over a public switched network .........................................................................................6-3
Figure 7-1. Power supply removal and installation...............................................................................................................7-3
Figure 7-2. M-DACS chassis mounting dimensions.............................................................................................................7-4
Figure
7-3. Terminal strip power connections IMUX 2000 M-DACS m
ultiplexers with single power supply modules ....7-7
Figure 7-4. Teminal strip power connections IMUX 2000 M-DACS multiplexers with redundant power s
upply modules7-8
Figure 7-5. Label on front door for recording input voltage configuration........................................................................7-11
Fi
gure 7-6. Caution Label inside front door of M-DACS..................................................................................................7-11
Fi
gure 7-7. Typical three-terminal IMUX 2000 M-DACS system ....................................................................................7-13
Figure 7-8. CM4 front panel LED indicators .....................................................................................................................
7-16
Fi
gure 7-9. CM4 front panel LED indicators.....................................................................................................................7-19
Fig
ure 7-10. Adding a new channel module to an existing system....................................................................................7-21