YASKAWA CR700

Standards Compliance
4
4.3 UL Standards
YASKAWA SIEPC71061723A YASKAWA AC Drive CR700 Technical Manual 279
Model Terminal
Recomm. Gauge
AWG, kcmil
Applicable Gauge
(IP20 Applicable
Gauge
*1
)
AWG, kcmil
Wire Stripping
Length
*2
mm
Terminal Screw
Tightening
Torque
N∙m (lbf∙in)
Terminal
Screw Size
Shape
2346
R/L1, S/L2, T/L3 250 × 2P
2/0 - 300 × 2P
(250 - 300 × 2P)
- M12 Hex self-locking nut
35
(310)
U/T1, V/T2, W/T3 250 × 2P
2/0 - 300 × 2P
(250 - 300 × 2P)
- M12 Hex self-locking nut
35
(310)
-, +1 350 × 2P
4/0 - 400 × 2P
(300 - 400 × 2P)
- M12 Hex self-locking nut
35
(310)
+3 3/0 × 2P
1/0 - 4/0 × 2P
(-)
- M12 Hex self-locking nut
35
(310)
1
1 - 350
(-)
- M12 Hex bolt (slotted)
32 - 40
(283 - 354)
2415
R/L1, S/L2, T/L3 250 × 2P
2/0 - 300 × 2P
(250 - 300 × 2P)
- M12 Hex self-locking nut
35
(310)
U/T1, V/T2, W/T3 300 × 2P
2/0 - 300 × 2P
(250 - 300 × 2P)
- M12 Hex self-locking nut
35
(310)
-, +1 350 × 2P
4/0 - 400 × 2P
(300 - 400 × 2P)
- M12 Hex self-locking nut
35
(310)
+3 3/0 × 2P
1/0 - 4/0 × 2P
(-)
- M12 Hex self-locking nut
35
(310)
1
1 - 350
(-)
- M12 Hex bolt (slotted)
32 - 40
(283 - 354)
*1 For IP20 protection, use wires that are in the range of applicable gauges.
*2 Remove insulation from the ends of wires to expose the length of wire shown.
*3 For wire gauges more than AWG 8, tighten to a tightening torque of 4.1 N∙m to 4.5 N∙m (36 lbf∙in to 40 lbf∙in).
*4 Terminals - and +1 have two screws. The Recommended Gauge is the wire gauge for one terminal.
*5 A junction terminal is necessary to connect a braking unit (CDBR-series) to terminals - and +3.
Three-Phase 400 V Class
Table 4.16 Main Circuit Wire Gauges and Tightening Torques (400 V Class)
Model Terminal
Recomm. Gauge
AWG, kcmil
Applicable
Gauge
(IP20 Applicable
Gauge
*1
)
AWG, kcmil
Wire Stripping
Length
*2
mm
Terminal Screw
Tightening
Torque
N∙m (lbf∙in)
Size Shape
4002
R/L1, S/L2, T/L3 14
14 - 6
(14 - 6)
10 M4 Slotted (-)
1.5 - 1.7
(13.5 - 15)
U/T1, V/T2, W/T3 14
14 - 6
(14 - 6)
10 M4 Slotted (-)
1.5 - 1.7
(13.5 - 15)
-, +1, +2 14
14 - 3
(14 - 3)
18 M5 Slotted (-)
2.3 - 2.5
(19.8 - 22)
*3
B1, B2 14
14 - 10
(14 - 10)
10 M4 Slotted (-)
1.5 - 1.7
(13.5 - 15)
12
14 - 8
(-)
- M4
Phillips/slotted
combo
1.2 - 1.5
(10.6 - 13.3)
4003
R/L1, S/L2, T/L3 14
14 - 6
(14 - 6)
10 M4 Slotted (-)
1.5 - 1.7
(13.5 - 15)
U/T1, V/T2, W/T3 14
14 - 6
(14 - 6)
10 M4 Slotted (-)
1.5 - 1.7
(13.5 - 15)
-, +1, +2 14
14 - 3
(14 - 3)
18 M5 Slotted (-)
2.3 - 2.5
(19.8 - 22)
*3
B1, B2 14
14 - 10
(14 - 10)
10 M4 Slotted (-)
1.5 - 1.7
(13.5 - 15)
12
14 - 8
(-)
- M4
Phillips/slotted
combo
1.2 - 1.5
(10.6 - 13.3)