YOKOGAWA UP55A - Using Larger, Smaller, Average, or Difference of Two to Four Inputs as PV; Setting Hysteresis and Dead Band for Position Proportional Control Output; Power Failure Recovery Processing; Power Frequency Setting; Other Settings; Maintenance

xii
IM 05P02C41-01EN
6.2 Performing and Canceling Auto-tuning ........................................................................... 6-26
6.3 AdjustingPIDManually .................................................................................................. 6-29
6.4 Setting Alarm Setpoint .................................................................................................... 6-34
6.5 Selecting Program Pattern Number (PTNO.) ................................................................. 6-35
6.6 Switching Operation Modes ........................................................................................... 6-36
6.6.1 Operation Display Switching Diagram .............................................................. 6-36
6.6.2 Switching to PROG Operation .......................................................................... 6-37
Selecting by RUN Key .......................................................................................................6-37
Selecting by Operation Mode Parameter ...........................................................................6-37
6.6.3 Switching to RESET Operation ......................................................................... 6-38
Selecting by RST Key ........................................................................................................6-38
Selecting by Operation Mode Parameter ...........................................................................6-38
6.6.4 Enabling/Disabling Hold Mode of Program Operation ...................................... 6-40
Selecting by MODE Key ....................................................................................................6-40
Selecting by Operation Mode Parameter ...........................................................................6-40
Hold Operation in Soak Segment ......................................................................................6-41
Hold Operation in Ramp Segment ..................................................................................... 6-41
6.6.5 Excuting Advance ............................................................................................. 6-42
Selecting by MODE Key ....................................................................................................6-42
Selecting by Operation Mode Parameter ...........................................................................6-42
6.6.6 Switching between AUTO and MAN ................................................................. 6-44
Selecting by MODE Key ....................................................................................................6-44
Selecting by Operation Mode Parameter ...........................................................................6-44
6.6.7 Switching to Local Operation ............................................................................ 6-46
Selecting by MODE Key ....................................................................................................6-46
Selecting by Operation Mode Parameter ...........................................................................6-46
6.6.8 Switching to Remote Operation ........................................................................ 6-47
Selecting by MODE Key ....................................................................................................6-47
Selecting by Operation Mode Parameter ...........................................................................6-47
6.6.9 Switching between Local (LSP) and Cascade .................................................. 6-48
Selecting by MODE Key ....................................................................................................6-48
Selecting by Operation Mode Parameter ...........................................................................6-48
6.7 Selecting Start-of-program Pattern Number ................................................................... 6-49
Selecting by MODE Key ....................................................................................................6-49
Selecting by Operation Mode Parameter ...........................................................................6-49
6.8 Fast-forwarding Program Pattern ................................................................................... 6-51
Performing by MODE Key .................................................................................................6-51
Performing by Operation Mode Parameter ........................................................................ 6-51
6.9 Changing SP, TSP, or Remaining Segment-time (R.TIM) in HOLD-mode ..................... 6-52
Changing SP in HOLD Operation ......................................................................................6-52
Changing TSP in HOLD Operation ....................................................................................6-53
Changing R.TIM in HOLD Operation .................................................................................6-53
Modifying Target Setpoint in Soak Segment ...................................................................... 6-55
Modifying Target Setpoint in Ramp Segment ....................................................................6-55
Modifying Final Target Setpoint (TSP) in Soak Segment ...................................................6-56
Modifying Final Target Setpoint (TSP) in Ramp Segment .................................................6-56
Decreasing Segment-time in Soak Segment ..................................................................... 6-57
Increasing Segment-time in Soak Segment ......................................................................6-58
Decreasing Segment-time in Ramp Segment ...................................................................6-59
Increasing Segment-time in Ramp Segment .....................................................................6-59
6.10 Changing Program Pattern during Program Operation ........................................................................ 6-60
6.11 Manipulating Control Output during Manual Operation ........................................................................ 6-61
6.12 Releasing On-State (Latch) of Alarm Output .................................................................. 6-63
Contents