To Next Page

To Previous Page

8-30

IM 05P02C41-01EN

LoopControlwithPVAuto-selector(2inputs)FunctionBlockDiagram

COM

Output limiter

Manual operation

Manual preset output

Input error preset output

Preset output

AUTO

When sensor

burnout occurs

Normal

MAN

RUNRESET

SP limiter

Input type

Input unit

Input range/scale

Analog input bias

Square root extraction

Analog input filter

10-seg. linearizer approx./bias

PV input bias

PV input filter

Ratio bias computation

PV auto-selector (Max., Min., Ave., Diff.)

Output limiter

A.BS

A.FL

PMD An, Bn

10-seg. linearizer approx./bias

PMD An, Bn

10-seg. linearizer approx./bias

PMD An, Bn

PV.AS

P.UNI P.DP P.RH, P.RL

CNT ALG

SPH, SPL

A.SR A.LC

UNIT

RH, RL

SDP

SH, SL

RSP

Input type

Input unit

Input range/scale

Analog input bias

Square root extraction

Analog input filter

A.BS

A.FL

A.SR A.LC

UNIT

RH, RL

SDP

SH, SL

EPO

OH, OL

OH, OL OLMT

MPON

Equipped as standard

For optional suffix code /HA

Heater break alarm

HAL2HAL1

Heater break

alarm 1

Heater break

alarm 2

Current or

voltage pulse

Relay Current

OUTOUT RET

PMD

OU.H OU.L

An, Bn

Split computation

10-seg. linearizer approx./bias

RET.H RET.L

PMD An, Bn

Split computation

10-seg. linearizer approx./bias

OUT retransmission output

O1RS

RET retransmission output

RTS

Output terminal assignment

Control computation

(Current when retransmission output)

PV input 1 PV input 2

Aux. analog (remote) input (E1-terminal area)

(for Standard model)

Suffix code: Type 2 = 1 or 4 is necessary.

Equipped as standard

* After the control output terminal is specified by the parameter OT,

other current output terminals can be used as retransmission output.

Sensor burnout occurs when PV or RSP input burnout occurs.

However, burnout is not detected if input is not conncted.

Terminal Parameter Function

Analog signal Contact signal Front panel key

Legend

PV display

SP display

Input ladder calculation program (signal goes to the control computation as is when without ladder program). For ladder program, see the LL50A Parameter Setting Software User’s Manual.

RMS

*1: RS-485, Ethernet, PROFIBUS-DP,

DeviceNet, CC-Link

Program pattern

Local target setpoint

Reset

TSP S.PID

PTNO.

TIME RAMP

L.PID

LSP

REM

LOC

RUN

RST

RBS

RESET/RUN switch

DI45DI44DI43DI42DI41DI3DI2DI1 DI16

Program pattern

selection

(Select a

number during a

RESET state.)

Contact inputs

(for Standard model)

DI16 is equipped when suffix code: Type 2 = 1 or 4.

DI41 to DI45 are equipped when suffix code: Type 2 = 0, 1, or 3.

Start of program operation

when DI changes from OFF to ON.

Stop of program operation

when DI changes from OFF to ON.

Start of local-mode operation

when DI changes from OFF to ON.

Start of remote-mode operation

when DI changes from OFF to ON.

For the model with optional suffix code /DR:

Remote input with direct input

(E1-terminal area) can be used

when suffix code: Type 2 = 1 or 4,

and with optional suffix code /DR.

However, DI16 is to be deleted.

RST

REM

A/M

LOC

RUN

AL3AL2AL1

PV event 1

PV event 2

PV event 3

Time event 1

Time event 2

Time event 3

Time event 4

DO23DO22DO21 DO24

Time event 5

DO25

PV event, Time event, Alarm

Output ladder calculation program (signal goes to the output as is when without ladder program). For ladder program, see the LL50A Parameter Setting Software User’s Manual.

DO31 to DO35 are assinged Time event

6 to 10.

(for Detailed model)

Optional suffix code /R1 is necessary.

(for Detailed model)

DI16 is equipped when optional suffix code /R1.

DI41 to DI45 are equipped when optional suffix code /X4.

For the model with optional suffix code /U1:

Remote input with direct input

(E1-terminal area) can be used

when optional suffix code /U1.

However, DI16 is to be deleted.