Allied Telesis AT-9724TS Reference Manual

Example usage:
To display all method lists for promoting user level privileges to administrator level privileges:
AT-9724TS:4# show authen_enable all
Command: show authen_enable all
Method List Name P r i o r i t y Method Name C o m m e n t
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
P e r m i t 1 t a c a c s + Built-in Group
2 t a c a c s Built-in Group
3 D a r r e n User-defined Group
4 l o c a l K e y w o r d
d e f a u l t 1 t a c a c s + Built-in Group
2 l o c a l K e y w o r d
Total Entries: 2
A T - 9 7 2 4 T S : 4 #
config authen application
Purpose Used to configure various applications on the Switch for authentication using a previously configured method
list.
Syntax config authen application [console | telnet | ssh | http | all] [login|enable][default|method
list name<string15>][login | enable] [default | method_list_name <string 15>]
Description This command is used to configure switch configuration applications (console, telnet, ssh, web) for login at the
user level and at the administration level (authen_enable) utilizing a previously configured method list.
Parameters application – Choose the application to configure.The user may choose one of the following four applications to
configure:
console – Choose this parameter to configure the command line interface login method.
telnet – Choose this parameter to configure the telnet login method.
ssh - Choose this parameter to configure the SSH (Secure Shell) login method.
http – Choose this parameter to configure the web interface login method.
all – Choose this parameter to configure all applications (console, telnet, web, ssh) login method.
login – Use this parameter to configure an application for normal login on the user level, using a previously
configured method list.
enable – Use this parameter to configure an application for upgrading a normal user level to administrator
privileges, using a previously configured method list.
default – Use this parameter to configure an application for user authentication using the default method list.
method_list_name <string 15> -– Use this parameter to configure an application for user authentication using a
previously configured method list. Enter a alphanumeric string of up to 15 characters to define a previously
configured method list.
Restrictions Only administrator-level users can issue this command.
Example usage:
To configure the default method list for the web interface:
AT-9724TS:4# config authen application http login default
Command: config authen application http login default
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
145
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g