Allied Telesis AT-9724TS Reference Manual

delete iproute default
Purpose Used to delete a default IP route entry from the Switch’s IP routing table.
Syntax delete iproute default <ipaddr>
Description This command will delete an existing default entry from the Switch’s IP routing table.
Parameters <ipaddr> – The gateway IP address for the next hop router.
Restrictions Only administrator-level users can issue this command.
Example usage:
To delete the default IP route 10.53.13.254:
AT-9724TS:4# delete iproute 10.48.74.121/8 10.1.1.254
Command: delete iproute 10.48.74.121/8 10.1.1.254
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
show iproute
Purpose Used to display the Switch’s current IP routing table.
Syntax show iproute {<network_address>} {[static | rip | ospf]}
Description This command will display the Switch’s current IP routing table.
Parameters <network_address> – IP address and netmask of the IP interface that is the destination of the route.The address
and mask information can be specified using the traditional format (for example, 10.1.2.3/255.0.0.0 or in CIDR
format, 10.1.2.3/8.
static – Use this parameter to display static iproute entries.
rip – Use this parameter to display RIP iproute entries.
ospf – Use this parameter to display OSPF iproute entries.
Restrictions None.
Example usage:
To display the contents of the IP routing table:
AT-9724TS:4# show iproute
Command: show iproute
IP Address/Netmask G a t e w a y I n t e r f a c e C o s t P r o t o c o l
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 . 0 . 0 . 0 1 0 . 1 . 1 . 2 5 4 S y s t e m 1 D e f a u l t
1 0 . 0 . 0 . 0 / 8 1 0 . 4 8 . 7 4 . 1 2 2 S y s t e m 1 L o c a l
Total Entries: 2
A T - 9 7 2 4 T S : 4 #
222
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g