Allied Telesis AT-9724TS Reference Manual

config radius
Purpose Used to configure the Switch’s RADIUS settings.
Syntax config radius <server_index 1-3> {ipaddress <server_ip> | key <passwd 32> | auth_port
<udp_port_number 1-65535> | acct_port <udp_port_number 1-65535>}
Description The config radius command is used to configure the Switch’s RADIUS server settings.
Parameters <server_index 1-3> – Assigns a number to the current set of RADIUS server settings. Up to 3 groups of
RADIUS server settings can be entered on the Switch.
ipaddress <server_ip> – The IP address of the RADIUS server.
key – Specifies that a password and encryption key will be used between the Switch and the RADIUS server.
<passwd 32> – The shared-secret key used by the RADIUS server and the Switch.Up to 32 characters can be
used.
auth_port <udp_port_number> – The UDP port number for authentication requests.The default is 1812.
acct_port <udp_port_number> – The UDP port number for accounting requests.The default is 1813.
Restrictions Only administrator-level users can issue this command.
Example usage:
To delete previously configured RADIUS server communication settings:
AT-9724TS:4# config radius 1 10.48.74.121 key Allied
Telesyn default
Command: config radius 1 10.48.74.121 key Allied Telesyn
d e f a u l t
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
show radius
Purpose Used to display the current RADIUS configurations on the Switch.
Syntax show radius
Description The show radius command is used to display the current RADIUS configurations on the Switch.
Parameters None.
Restrictions None.
Example usage:
To display RADIUS settings on the Switch:
AT-9724TS:4# show radius
Command: show radius
I d x I P A d d r e s s A u t h - P o r t A c c t - P o r t S t a t u s K e y
N u m b e r N u m b e r
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 1 0 . 1 . 1 . 1 1 8 1 2 1 8 1 3 A c t i v e s w i t c h
2 2 0 . 1 . 1 . 1 1 8 0 0 1 8 1 3 A c t i v e d e s 3 2 2 6
3 3 0 . 1 . 1 . 1 1 8 1 2 1 8 1 3 A c t i v e a l l i e d t e l e s y n
Total Entries: 3
A T - 9 7 2 4 T S : 4 #
179
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g