Allied Telesis AT-9724TS Reference Manual

create snmp community
Purpose Used to create an SNMP community string to define the relationship between the SNMP manager and an
agent.The community string acts like a password to permit access to the agent on the Switch. One or more of
the following characteristics can be associated with the community string:
An Access List of IP addresses of SNMP managers that are permitted to use the community string to gain
access to the Switch’s SNMP agent.
An MIB view that defines the subset of all MIB objects that will be accessible to the SNMP community.
Read-write or read-only level permission for the MIB objects accessible to the SNMP community.
Syntax create snmp community <community_string 32> view <view_name 32> [read_only |
read_write]
Description The create snmp community command is used to create an SNMP community string and to assign
access-limiting characteristics to this community string.
Parameters <community_string 32> – An alphanumeric string of up to 32 characters that is used to identify members of an
SNMP community.This string is used like a password to give remote SNMP managers access to MIB objects in
the Switch’s SNMP agent.
view <view_name 32> – An alphanumeric string of up to 32 characters that is used to identify the group of MIB
objects that a remote SNMP manager is allowed to access on the Switch.
read_only – Specifies that SNMP community members using the community string created with this command
can only read the contents of the MIBs on the Switch.
read_write – Specifies that SNMP community members using the community string created with this command
can read from and write to the contents of the MIBs on the Switch.
Restrictions Only administrator-level users can issue this command.
Example usage:
To create the SNMP community string “Allied Telesyn”:
AT-9724TS:4# create snmp community Allied Telesyn
view ReadView read_write
Command: create snmp community Allied Telesyn
view ReadView read_write
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
delete snmp community
Purpose Used to remove a specific SNMP community string from the Switch.
Syntax delete snmp community <community_string 32>
Description The delete snmp community command is used to remove a previously defined SNMP community string
from the Switch.
Parameters <community_string 32> – An alphanumeric string of up to 32 characters that is used to identify members of an
SNMP community.This string is used like a password to give remote SNMP managers access to MIB objects in
the Switch’s SNMP agent.
Restrictions Only administrator-level users can issue this command.
Example usage:
To delete the SNMP community string “Allied Telesyn”:
AT-9724TS:4# delete snmp community Allied Telesyn
Command: delete snmp community Allied Telesyn
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
38
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g