Allied Telesis AT-9724TS Reference Manual

Chapter 41 - OSPF Configuration Commands
The OSPF configuration commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.
Command Parameters
config ospf router_id <ipaddr>
enable ospf
disable ospf
show ospf
create ospf area <area_id> type [normal | stub {stub_summary [enable | disable] | metric <value 0-65535>}]
delete ospf area <area_id>
config ospf area <area_id> type [normal | stub {stub_summary [enable | disable] | metric <value 0-65535>}]
show ospf area {<area_id>}
create ospf host_route <ipaddr> {area <area_id> | metric <value 1-65535>}
delete ospf host_route <ipaddr>
config ospf host_route <ipaddr> {area <area_id> | metric <value 1-65535>}
show ospf host_route <ipaddr>
create ospf aggregation <area_id> <network_address> lsdb_type summary {advertise [enable | disable]}
delete ospf aggregation <area_id> <network_address> lsdb_type summary
config ospf aggregation <area_id> <network_address> lsdb_type summary {advertise [enable | disable]}
show ospf aggregation <area_id>
show ospf lsdb {area <area_id> | advertise_router <ipaddr> | type [rtrlink | netlink | summary | assummary | asextlink]}
show ospf neighbor <ipaddr>
show ospf virtual_neighbor {<area_id> <neighbor_id>}
config ospf ipif <ipif_name 12> {area <area_id> | priority <value> | hello_interval <sec 1-65535 > | dead_interval <sec 1-
65535> | authentication [none | simple <password 8> | md5 <key_id 1-255>] | metric <value 1-65535> state
[enable | disable]
config ospf all {area <area_id> | priority <value> | hello_interval <1-65535 sec> | dead_interval <1-65535 sec> |
authentication [none | simple <password 8> | md5 <key_id 1-255>] | metric <value 1-65535> state [enable |
disable]
show ospf ipif <ipif_name 12>
show ospf all
create ospf virtual_link <area_id> <neighbor_id> {hello_interval <sec 1-65535> | dead_interval <sec 1-65535> | authentication [none
| simple <password 8> | md5 <key_id 1-255>]}
config ospf virtual_link <area_id> <neighbor_id> {hello_interval <sec 1-65535> | dead_interval <sec 1-65535> | authentication [none
| simple <password 8> | md5 <key_id 1-255>]}
delete ospf virtual_link <area_id> <neighbor_id>
show ospf virtual_link <area_id> <neighbor_id>
Each command is listed, in detail, in the following sections.
250
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g