Allied Telesis AT-9724TS Reference Manual

Chapter 24 - 802.1X Commands
The AT-9724TS implements the server-side of the IEEE 802.1x Port-based and MAC-based Network Access Control.This mechanism is intended to allow only
authorized users, or other network devices, access to network resources by establishing criteria for each port on the Switch that a user or network device must
meet before allowing that port to forward or receive frames.
Command Parameters
enable 802.1x
disable 802.1x
create 802.1x user <username 15>
show 802.1x user
delete 802.1x user
show 802.1x auth_state ports [<portlist> | all]
show 802.1x auth_configuration ports [<portlist> | all]
config 802.1x auth_mode [port_based | mac_based]
config 802.1x capability [ports <portlist> | all] [authenticator | none]
config 802.1x auth_parameter ports [<portlist> | all] [default | {direction [both | in] | port_control [force_unauth | auto | force_auth] |
quiet_period <sec 0-65535> | tx_period <sec 1-65535> | supp_timeout <sec 1-65535> | server_timeout <sec
1-65535> | max_req <value 1-10> | reauth_period <sec 1-65535> | enable_reauth [enable | disable]}]
config 802.1x auth_protocol [local | radius eap]
config 802.1x init {port_based ports [<portlist> | all]} | mac_based [ports] [<portlist> | all] {mac_address <macaddr>}]
config 802.1x reauth {port_based ports [<portlist> | all]} [<portlist> | all] {mac_address <macaddr>}]
config radius add <server_index 1-3> <server_ip> key <passwd 32> [default {auth_port <udp_port_number 1-65535> |
acct_port <udp_port_number 1-65535>}]
<server_index 1-3>
<server_index 1-3> {ipaddress <server_ip> | key <passwd 32> [auth_port <udp_port_number 1-65535> acct_port <udp_port_number 1-65535>]}
show radius
show acct_client
show auth_client
show auth_diagnostics {ports [<portlist> | all]}
show auth_session statistics {ports [<portlist> | all]}
show auth_statistics {ports [<portlist> | all]}
Each command is listed, in detail, in the following sections.
enable 802.1x
Purpose Used to enable the 802.1x server on the Switch.
Syntax enable 802.1x
Description The enable 802.1x command enables the 802.1x Network Access control server application on the Switch.
To select between port-based or MAC-based, use the config 802.1x auth_mode command.
Parameters None.
Restrictions Only administrator-level users can issue this command.
Example usage:
To enable 802.1x switch wide:
AT-9724TS:4# enable 802.1x
Command: enable 802.1x
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
167
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g