Allied Telesis AT-9724TS Reference Manual

Chapter 29 - Time and SNTP Commands
The Simple Network Time Protocol (SNTP) {an adaptation of the Network Time Protocol (NPT)} commands in the Command Line Interface (CLI) are listed
(along with the appropriate parameters) in the following table.
Command Parameters
config sntp {primary <ipaddr> | secondary <ipaddr> | poll-interval <int 30-99999>}
show sntp
enable sntp
disable sntp
config time <date ddmthyyyy > <time hh:mm:ss>
config time_zone {operator [+ | -] | hour <gmt_hour 0-13> | min <minute 0-59>}
config dst [disable | repeating {s_week <start_week 1-4,last> | s_day <start_day sun-sat>| s_mth <start_mth 1-12> |
s_time <start_time hh:mm> | e_week <end_week 1-4,last> | e-day <end_day sun-sat> | e_mth <end_mth 1-
12> | e_time <end_time hh:mm> | offset [30 | 60 | 90 | 120]} | annual {s_date <start_date 1-31> | s_mth
<start_mth 1-12> | s_time <start_time hh:mm> | e_date <end_date 1-31> | e_mth <end_mth 1-12> | e_time
<end_time hh:mm> | offset [30 | 60 | 90 | 120]}]
show time
Each command is listed, in detail, in the following sections:
config sntp
Purpose Used to setup SNTP service.
Syntax config sntp {primary <ipaddr> | secondary <ipaddr> | poll-interval <int 30-99999>}
Description Use this command to configure SNTP service from an NTP server. SNTP must be enabled for this command to
function (See enable sntp).
Parameters primary – This is the primary server the SNTP information will be taken from.
<ipaddr> – The IP address of the primary server.
secondary – This is the secondary server the SNTP information will be taken from in the event the primary
server is unavailable.
<ipaddr> – The IP address for the secondary server.
poll-interval <int 30-99999> – This is the interval between requests for updated SNTP information.The polling
interval ranges from 30 to 99,999 seconds.
Restrictions Only administrator-level users can issue this command. SNTP service must be enabled for this command to
function (enable service must be enabled for this command to function (enable sntp).
Example usage:
To configure SNTP settings:
AT-9724TS:4# config sntp primary 10.1.1.1 secondary
10.1.1.2 poll-interval 30
Command: config sntp primary 10.1.1.1 secondary
10.1.1.2 poll-interval 30
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
205
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g