Allied Telesis AT-9724TS Reference Manual

config radius add
Purpose Used to add a new RADIUS server.
Syntax config radius add <server_index 1-3> <server_ip> key <passwd 32> [default | {auth_port
<udp_port_number 1-65535> | acct_port <udp_port_number 1-65535>}]
Description The config radius add command is used to add RADIUS servers to the Switch.
Parameters <server_index 1-3> – Assigns a number to the current set of RADIUS server settings. Up to 3 groups of
RADIUS server settings can be entered on the Switch.The lowest index number will have a higher
authenticative priority.
<server_ip> – The IP address of the RADIUS server.
key – Specifies that a password and encryption key will be used between the Switch and the RADIUS server.
<passwd 32> – The shared-secret key used by the RADIUS server and the Switch.
Up to 32 characters can be used.
default – Uses the default UDP port number in both the “auth_port” and “acct_port” settings.
auth_port <udp_port_number> – The UDP port number for authentication requests.The default is 1812.
acct_port <udp_port_number> – The UDP port number for accounting requests.The default is 1813.
Restrictions Only administrator-level users can issue this command.
Example usage:
To configure the RADIUS server communication settings:
AT-9724TS:4# config radius add 1 10.48.74.121 key Allied
Telesyn default
Command: config radius add 1 10.48.74.121 key Allied
Telesyn default
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
config radius delete
Purpose Used to delete a previously entered RADIUS server configuration.
Syntax config radius delete <server_index 1-3>
Description The config radius delete command is used to delete a previously entered RADIUS server configuration.
Parameters <server_index 1-3> – A number identifying the current set of RADIUS server settings the user wishes to delete.
Up to 3 groups of RADIUS server settings can be entered on the Switch.
Restrictions Only administrator-level users can issue this command.
Example usage:
To delete previously configured RADIUS server communication settings:
AT-9724TS:4# config radius delete 1
Command: config radius delete 1
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
178
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g