Allied Telesis AT-9724TS Reference Manual

Each command is listed, in detail, in the following sections.
create snmp user
Purpose Used to create a new SNMP user and adds the user to an SNMP group that is also created by this command.
Syntax create snmp user <SNMP_name 32> <groupname 32> {encrypted [by_password auth
[md5 <auth_password 8-16> | sha <auth_password 8-20>] priv [none | des
<priv_password 8-16>] | by_key auth [md5 <auth_key 32-32> | sha <auth_key 40-40>]
priv [none | des <priv_key 32-32>]]}
Description The create snmp user command creates a new SNMP user and adds the user to an SNMP group that is
also created by this command. SNMP ensures:
Message integrity – Ensures that packets have not been tampered with during transit.
Authentication – Determines if an SNMP message is from a valid source.
Encryption – Scrambles the contents of messages to prevent it from being viewed by an unauthorized source.
create snmp view <view_name 32> <oid> view
Parameters <username 32> – An alphanumeric name of up to 32 characters that will identify the new SNMP user.
<groupname 32> – An alphanumeric name of up to 32 characters that will identify the SNMP group the new
SNMP user will be associated with.
encrypted – Allows the user to choose a type of authorization for authentication using SNMP.The user may
choose:
by_password – Requires the SNMP user to enter a password for authentication and privacy.The password is
defined by specifying the auth_password below.This method is recommended.
by_key – Requires the SNMP user to enter a encryption key for authentication and privacy.The key is defined
by specifying the key in hex form below.This method is not recommended.
auth – The user may also choose the type of authentication algorithms used to authenticate the snmp user.The
choices are:
md5 – Specifies that the HMAC-MD5-96 authentication level will be used. md5 may be utilized by entering one
of the following:
<auth password 8-16> – An alphanumeric sting of between 8 and 16 characters that will be used to authorize
the agent to receive packets for the host.
<auth_key 32-32> – Enter an alphanumeric sting of exactly 32 characters, in hex form, to define the key that
will be used to authorize the agent to receive packets for the host.
sha – Specifies that the HMAC-SHA-96 authentication level will be used.
<auth password 8-20> – An alphanumeric sting of between 8 and 20 characters that will be used to authorize
the agent to receive packets for the host.
<auth_key 40-40> – Enter an alphanumeric sting of exactly 40 characters, in hex form, to define the key that
will be used to authorize the agent to receive packets for the host.
priv – Adding the priv (privacy) parameter will allow for encryption in addition to the authentication algorithm
for higher security.The user may choose:
des – Adding this parameter will allow for a 56-bit encryption to be added using the DES-56 standard using:
<priv_password 8-16> – An alphanumeric string of between 8 and 16 characters that will be used to encrypt
the contents of messages the host sends to the agent.
<priv_key 32-32> – Enter an alphanumeric key string of exactly 32 characters,in hex form, that will be used to
encrypt the contents of messages the host sends to the agent.
none – Adding this parameter will add no encryption.
Restrictions Only administrator-level users can issue this command.
34
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g