Allied Telesis AT-9724TS Reference Manual

Chapter 36 - RIP Commands
The RIP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.
Command Parameters
config rip [ipif <ipif_name 12> | all] {authentication [enable <password 16> | disable] | tx_mode [disable | v1_only |
v1_compatible | v2_only] | rx_mode [v1_only | v2_only | v1_or_v2 | disable] state [enable | disable]}
enable rip
disable rip
show rip ipif <ipif_name 12>
Each command is listed, in detail, in the following sections.
config rip
Purpose Used to configure RIP on the Switch.
Syntax config rip [ipif <ipif_name 12> | all] {authentication [enable <password 16> | disable] |
tx_mode [disable | v1_only | v1_compatible | v2_only] | rx_mode [v1_only | v2_only |
v1_or_v2 | disable] state [enable | disable]}
Description This command is used to configure RIP on the Switch.
Parameters <ipif_name 12> – The name of the IP interface.
all – To configure all RIP receiving mode for all IP interfaces.
authentication [enable | disable] – Enables or disables authentication for RIP on the Switch.
<password 16> – Allows the specification of a case-sensitive password.
tx_mode – Determines how received RIP packets will be interpreted – as RIP version V1 only,V2 Only, or V1
Compatible (V1 and V2).This entry specifies which version of the RIP protocol will be used to transfer RIP
packets.The disabled entry prevents the reception of RIP packets.
disable – Prevents the transmission of RIP packets.
v1_only – Specifies that only RIP v1 packets will be transmitted.
v1_compatible – Specifies that only RIP v1 compatible packets will be transmitted.
v2_only – Specifies that only RIP v2 packets will be transmitted.
rx_mode – Determines how received RIP packets will be interpreted – as RIP version V1 only,V2 Only, or V1 or
V2.This entry specifies which version of the RIP protocol will be used to receive RIP packets.The Disabled
entry prevents the reception of RIP packets.
v1_only – Specifies that only RIP v1 packets will be transmitted.
v2_only – Specifies that only RIP v2 packets will be transmitted.
v1_or_v2 – Specifies that only RIP v1 or v2 packets will be transmitted.
state [enable | disable] – Allows RIP to be enabled and disabled on the Switch.
Restrictions Only administrator-level users can issue this command.
Example usage:
To change the RIP receive mode for the IP interface System:
AT-9724TS:4# config rip ipif System rx_mode v1_only
Command: config rip ipif System rx_mode v1_only
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
236
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g