Allied Telesis AT-9724TS Reference Manual

show auth_diagnostics
Purpose Used to display the current authentication diagnostics.
Syntax show auth_diagnostics {ports [<portlist> | all]}
Description The show auth_diagnostics command is used to display the current authentication diagnostics of the
Switch on a per port basis.
Parameters ports <portlist> – Specifies a range of ports.The port list is specified by listing the lowest switch number and the
beginning port number on that switch, separated by a colon.Then the highest switch number, and the highest
port number of the range (also separated by a colon) are specified.The beginning and end of the port list range
are separated by a dash. For example, 1:3 specifies switch number 1, port 3. 2:4 specifies switch number 2, port
4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2,port 4 – in numerical order.
all – Specifies that all ports will be viewed.
Restrictions None.
Example usage:
To display the current authentication diagnostics for port 16:
AT-9724TS:4# show auth_diagnostics ports 1:16
Command: show auth_diagnostics ports 1:16
Port number: 1 : 1 6
E n t e r s C o n n e c t i n g 0
E a p L o g o f f s W h i l e C o n n e c t i n g 0
E n t e r s A u t h e n t i c a t i n g 0
S u c c e s s W h i l e A u t h e n t i c a t i n g 0
T i m e o u t s W h i l e A u t h e n t i c a t i n g 0
F a i l W h i l e A u t h e n t i c a t i n g 0
R e a u t h s W h i l e A u t h e n t i c a t i n g 0
E a p L o g o f f W h i l e A u t h e n t i c a t i n g 0
R e a u t h s W h i l e A u t h e n t i c a t e d 0
E a p S t a r t s W h i l e A u t h e n t i c a t e d 0
E a p L o g o f f W h i l e A u t h e n t i c a t e d 0
B a c k e n d R e s p o n s e s 0
B a c k e n d A c c e s s C h a l l e n g e s 0
B a c k e n d O t h e r R e q u e s t s T o S u p p l i c a n t 0
B a c k e n d N o n N a k R e s p o n s e s F r o m S u p p l i c a n t 0
B a c k e n d A u t h S u c c e s s e s 0
B a c k e n d A u t h F a i l s 0
CTRL+C ESC q Quit SPACE n Next Page Enter Next Entry a All
182
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g