AudioCodes Media 800 MSBR - Page 920

User's Manual 920 Document #: LTRT-12809
Mediant 800 MSBR
Parameter Description
[EnableDSPIPMDetecto
rs]

For this parameter to take effect, a device reset is required.
 The device's Software License Key must contain the 'IPMDetector'
DSP option.
 When enabled (1), the number of available channels is reduced.
Web: Add IE in SETUP
EMS: IE To Be Added In
Q.931 Setup
CLI: add-ie-in-setup
[AddIEinSetup]
Adds an optional Information Element (IE) data (in hex format) to ISDN
Setup messages. For example, to add IE '0x20,0x02,0x00,0xe1', enter
the value "200200e1".
Notes:
 This IE is sent from the Trunk Group IDs that are defined by the
parameter SendIEonTG.
 You can configure different IE data for Trunk Groups by defining this
parameter for different IP Profiles (using the IPProfile parameter)
and then assigning the required IP Profile ID in the Inbound IP
Routing Table (PSTNPrefix).
 This feature is similar to that of the EnableISDNTunnelingIP2Tel
parameter. If both parameters are configured, the
EnableISDNTunnelingIP2Tel parameter takes precedence.
Web: Trunk Groups to
Send IE
EMS: List Of Trunk
Groups To Send IE
CLI: trkgrps-to-snd-ie
[SendIEonTG]
Defines Trunk Group IDs (up to 50 characters) from where the optional
ISDN IE (defined by the parameter AddIEinSetup) is sent. For example:
'1,2,4,10,12,6'.
Notes:
 You can configure different IE data for Trunk Groups by defining this
parameter for different IP Profile IDs (using the parameter IPProfile),
and then assigning the required IP Profile ID in the Inbound IP
Routing Table (PSTNPrefix).
 When IP Profiles are used for configuring different IE data for Trunk
Groups, this parameter is ignored.
Web: Enable User-to-
User IE for Tel to IP
EMS: Enable UUI Tel 2
Ip
CLI: uui-ie-for-tel2ip
[EnableUUITel2IP]
Enables transfer of User-to-User (UU) IE from ISDN PRI to SIP.
 [0] Disable (default)
 [1] Enable
The device supports the following ISDN PRI-to-SIP interworking: Setup
to SIP INVITE, Connect to SIP 200 OK, User Information to SIP INFO,
Alerting to SIP 18x response, and Disconnect to SIP BYE response
messages.
Note: The interworking of ISDN User-to-User IE to SIP INFO is
applicable only to the Euro ISDN, QSIG, and 4ESS PRI variants.
Web: Enable User-to-
User IE for IP to Tel
EMS: Enable UUI Ip 2
Tel
CLI: uui-ie-for-ip2tel
[EnableUUIIP2Tel]
Enables interworking of SIP user-to-user information (UUI) to User-to-
User IE in ISDN Q.931 messages.
 [0] Disable = (Default) Received UUI is not sent in ISDN message.
 [1] Enable = The device interworks UUI from SIP to ISDN
messages. The device supports the following SIP-to-ISDN
interworking of UUI:

SIP INVITE to Q.931 Setup

SIP REFER to Q.931 Setup

SIP 200 OK to Q.931 Connect

SIP INFO to Q.931 User Information

SIP 18x to Q.931 Alerting

SIP BYE to Q.931 Disconnect
Notes:
 The interworking of ISDN User-to-User IE to SIP INFO is applicable
only to the Euro ISDN, QSIG, and 4ESS PRI variants.