Canon E1 - Page 177

Items
Service Mode
(COPIER> FUNCTION)
Use case Remarks
Drive of Middle Deck Lift-
er Motor
CST> MD-LIFT2
CST> MD2LIFT2 *
At recovery from descent timeout alarm
Drive of Lower Deck Lift-
er Motor
CST> MD-LIFT3
CST> MD2LIFT3 *
At recovery from descent timeout alarm
Adjusting the position of
Multi-purpose Tray: MD
CST> MD-MF-RG - At installation of the Multi-purpose Tray
- When jam occurs for position gap of the
Multi-purpose Tray and the Alignment
Plate of the Through Path Unit.
Adjusting the position of
POD Deck Lite: MD
CST> MD-DK-RG - At installation of the POD Deck Lite
- When jam occurs for position gap of the
POD Deck Lite and the Alignment Plate of
the Through Path Unit.
■ Functional Setting Items
*: For Secondary Multi-drawer Paper Deck
Items
Service Mode
(COPIER> OPTION)
Use case Remarks
Adjusting paper level for
Multi Deck (Upper)
FEED-SW> DK5-REST
FEED-SW> DK8-REST *
Upon user's request
Adjusting paper level for
Multi Deck (Middle)
FEED-SW> DK6-REST
FEED-SW> DK9-REST *
Upon user's request
Adjusting paper level for
Multi Deck (Lower)
FEED-SW> DK7-REST
FEED-SW> DK10REST *
Upon user's request
Setting paper surface
level down: Deck standby
FEED-SW> DK1-LDWN
FEED-SW> DK2-LDWN *
When Pickup Roller trace occurs on trans-
parency or the 1st sheet of coated paper in
an LL environment.
Setting swing half-open
mode: MD, Upper
FEED-SW> MD-ALV1
FEED-SW> MD2-ALV1 *
If double feeding or pickup failure occurs
when paper weighing 151 g/m
2
or less is
fed with the air assist set to ON the Upper
Deck of the Multi Deck.
Setting swing half-open
mode: MD, Middle
FEED-SW> MD-ALV2
FEED-SW> MD2-ALV2 *
If double feeding or pickup failure occurs
when paper weighing 151 g/m
2
or less is
fed with the air assist set to ON the Middle
Deck of the Multi Deck.
Setting swing half-open
mode: MD, Lower
FEED-SW> MD-ALV3
FEED-SW> MD2-ALV3 *
If double feeding or pickup failure occurs
when paper weighing 151 g/m
2
or less is
fed with the air assist set to ON the Lower
Deck of the Multi Deck.
Setting ON/OFF of Multi
Deck (Upper) air assist
FEED-SW> MD-AIR1
FEED-SW> MD2-AIR1 *
- When a jam or double feed error frequent-
ly occurs with plain paper or heavy paper 1
- When the transfer performance is low with
coated paper, textured paper, etc.
When set the value 3, an air
capacity control is necessary
in the user mode.
Setting ON/OFF of Multi
Deck (Middle) air assist
FEED-SW> MD-AIR2
FEED-SW> MD2-AIR2 *
- When a jam or double feed error frequent-
ly occurs with plain paper or heavy paper 1
- When the transfer performance is low with
coated paper, textured paper, etc.
When set the value 3, an air
capacity control is necessary
in the user mode.
Setting ON/OFF of Multi
Deck (Lower) air assist
FEED-SW> MD-AIR3
FEED-SW> MD2-AIR3 *
- When a jam or double feed error frequent-
ly occurs with plain paper or heavy paper 1
- When the transfer performance is low with
coated paper, textured paper, etc.
When set the value 3, an air
capacity control is necessary
in the user mode.
Setting of MD (Upper)
Pickup Roll engage/
disengage
FEED-SW> MD-PSP1
FEED-SW> MD2-PSP1 *
When Pickup Roller trace occurs on the
2nd sheets and later
If the machine is continued to
be used while the setting val-
ue is 1, the life of the solenoid
becomes shorter.
Setting of MD (Middle)
Pickup Roll engage/
disengage
FEED-SW> MD-PSP2
FEED-SW> MD2-PSP2 *
When Pickup Roller trace occurs on the
2nd sheets and later
If the machine is continued to
be used while the setting val-
ue is 1, the life of the solenoid
becomes shorter.
5. Adjustment
169