Cisco Catalyst 3750-X Command Reference

2-434
Catalyst 3750-X and 3560-X Switch Command Reference
OL-29704-01
Chapter 2 Catalyst 3750-X and 3560-X Switch Cisco IOS Commands
monitor session
dot1q vlan vlan-id Accept incoming packets with IEEE 802.1Q encapsulation with the
specified VLAN as the default VLAN.
isl Specify ingress forwarding using ISL encapsulation.
untagged vlan vlan-id Accept incoming packets with untagged encapsulation with the specified
VLAN as the default VLAN.
vlan vlan-id When used with only the ingress keyword, set default VLAN for ingress
traffic.
remote vlan vlan-id Specify the remote VLAN for an RSPAN source or destination session. The
range is 2 to 1001 and 1006 to 4094.
The RSPAN VLAN cannot be VLAN 1 (the default VLAN) or VLAN IDs
1002 to 1005 (reserved for Token Ring and FDDI VLANs).
destination-port group
{a | b | c}
This option is only supported on the Catalyst 3560-E-12D aggregator
switch.
Specify the destination-port group to which the destination ports belong if
you are configuring a RSPAN source session.
The switch supports these destination-port groups depending on the switch
port configuration:
• a—tengigabitethernet 0/1 to tengigabitethernet 0/4 or
gigabitethernet 0/1 to gigabitethernet 0/8
• b—tengigabitethernet 0/5 to tengigabitethernet 0/8 or
gigabitethernet 0/9 to gigabitethernet 0/16
• c—tengigabitethernet 0/9 to tengigabitethernet 0/12 or
gigabitethernet 0/17 to gigabitethernet 0/24
, (Optional) Specify a series of interfaces or VLANs, or separate a range of
interfaces or VLANs from a previous range. Enter a space before and after
the comma.
- (Optional) Specify a range of interfaces or VLANs. Enter a space before
and after the hyphen.
filter vlan vlan-id Specify a list of VLANs as filters on trunk source ports to limit SPAN
source traffic to specific VLANs. The vlan-id range is 1 to 4094.
source Specify the SPAN or RSPAN source. A source can be a physical port, a port
channel, or a VLAN.
both, rx, tx (Optional) Specify the traffic direction to monitor. If you do not specify a
traffic direction, the source interface sends both transmitted and received
traffic.
source vlan vlan-id Specify the SPAN source interface as a VLAN ID. The range is 1 to 4094.
all, local, remote Specify all, local, or remote with the no monitor session command to clear
all SPAN and RSPAN, all local SPAN, or all RSPAN sessions.
filter ip Specify the filtering of IPv4 packets in an FSPAN session.
filter ipv6 Specify the filtering of IPv6 packets in an FSPAN session.
filter mac Specify the filtering of non-IP packets in an FSPAN session.
access-group
access-list-number, name
Specify the access list numbers or names to apply to an FSPAN session.

Cisco Catalyst 3750-X Specifications

General

Switching Capacity	160 Gbps
Stacking Bandwidth	64 Gbps
Max Stacking Units	9
Layer Support	Layer 2 and Layer 3
Form Factor	Rack-mountable
DRAM	256 MB
Flash Memory	64 MB
Model	Cisco Catalyst 3750-X Series
Ports	24 or 48 10/100/1000 Ethernet ports
Uplink Interfaces	4 SFP or 2 SFP+
Features	StackWise Plus, EnergyWise
Image	IP Base or IP Services
Operating Temperature	0 to 40°C
Operating Humidity	10 to 85% noncondensing