D-Link DWC-1000 User Manual

D-Link DWC-1000 User Manual 368
Section 10 - Troubleshooting
Using the Reset Button to Restore Default Settings
If you cannot access the wireless controller’s management interface for some reason, press the reset button on
the front panel to restore the factory default settings.
To clear all settings and restore the factory default values:
1. Press and hold the reset button for at least 15 seconds.
2. Release the reset button. The reboot process is complete after several minutes.
Note: After restoring the factory default conguration, the wireless controller’s default LAN IP address is 192.168.10.1,
the default login user name is admin, and the default login password is admin.
Problems with Date and Time
The Date and Time page shows the current date and time of day. The wireless controller uses the Network Time
Protocol (NTP) to obtain the current time from one of several network time servers on the Internet. Each entry in
the log is stamped with the date and time of day.
If you nd that the date and time stamps are not accurate,
• Conrm that the wireless controller can reach the Internet.
• If you have just congured the controller, wait for at least 5 minutes, select Administration > Date and
Time > Time Zone, and recheck the date and time.
• Verify your internet access settings.
If you nd that the time is o by an hour,
• Select Administration > Date and Time > Time Zone, and view the current date and time settings.
• Toggle the switch to Enable or Disable “Daylight Savings”, then click Save.
Discovery Problems with Access Points
If the wireless controller does not discover any or all access points:
• Be sure the wireless controller is connected to the LAN (see “LAN Port LEDs Not ON” on page 366).
• Be sure you entered the appropriate IP address range if the access points operate in dierent VLANs,
reside behind an IP subnet, or operate in standalone mode (see “Step #1: Enable DHCP Server (Optional)”
on page 28).
• If you are using a rewall, unblock the UDP port number for each access port in the rewall.
• Be sure each access point is using a unique IP address (see “AP Discovery Methods” on page 95). If
more than one access point has the same IP address, only one of them is discovered. In this case, add
the access point to the managed list, change its IP address, and then run discovery again to discover the
next access point with that IP address (see “Step #3: Select APs to be Managed” on page 30).

D-Link DWC-1000 Specifications

General

Ethernet LAN	Yes
Wi-Fi standards	802.11a, 802.11b, 802.11g
Networking standards	IEEE 802.1Q, IEEE 802.1x, IEEE 802.3, IEEE 802.3ad, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Number of managed Wi-Fi Access Points (max)	6
Security algorithms	3DES, DES, WEP, WPA, WPA2
USB 2.0 ports quantity	2
Ethernet LAN (RJ-45) ports	4
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	0
Certification	FCC B, CE B, VCCI, C-tick, IC, cUL, LVD (EN60950-1)
Built-in display	No
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	5 - 95 %
Power requirements	DC 12V/2.5A
Power consumption (typical)	19.3 W
Pallet width	1200 mm
Pallet length	1100 mm
Pallet height (air)	1419 mm
Pallet height (sea)	1847 mm
Pallet gross weight (air)	415236 g
Pallet gross weight (sea)	545648 g
Quantity per pallet (air)	144 pc(s)
Quantity per pallet (sea)	192 pc(s)
Shipping (inner) case width	296 mm
Shipping (inner) case height	428 mm
Shipping (inner) case length	354 mm
Shipping (inner) case weight	10826 g
Shipping (inner) case net weight	10016 g
Number of cartons per pallet (air)	36 pc(s)
Number of cartons per pallet (sea)	48 pc(s)
Quantity per shipping (inner) case	4 pc(s)

Weight and Dimensions

Package depth	396 mm
Package width	273 mm
Package height	80 mm
Package weight	2504 g
Dimensions (WxDxH)	280 x 180 x 44 mm