Safety
34
Pos: 13.6.17 /Überschr iften/Überschr iften 2/U-Z/War tung @ 33\mod_1254222340957_ 78.docx @ 318599 @ 2 @ 1
4.8 Maintenance
Pos: 13.6.18 /BA/S icherheit/Wartung/ Wartung Pos.1 mit Schwung mass/Feststellbre mse anziehen @ 17\mod_123623 9859956_78.doc x @ 203295 @ @ 1
1 Always make certain that the drive and the engine are switched off before doing any
repairs, maintenance or cleaning! Remove ignition key! Secure the flywheel with the
parking brake.
Pos: 13.6.19 /BA/S icherheit/Wartung/ Wartung Pos.2 bis 8 mit Elek tronik @ 17\mod_123623909 9566_78.docx @ 203245 @ @ 1
2 Regularly check that nuts and bolts are properly seated and tighten if necessary!
3 When performing maintenance work with the machine raised, always secure it with
suitable supporting elements!
4 Oils, greases and filters must be disposed of correctly!
5 Always disconnect the power supply before working on the electrical system!
6 If protective devices and guards are subject to wear, check them regularly and replace
them in good time!
7 When performing electrical welding work on the vehicle and mounted devices, turn power
supply off at main battery switch or disconnect generator cable and battery!
8 Replacement parts must at least comply with the technical requirements set by the
manufacturer of the implements! This is guaranteed by original KRONE spare parts!
Pos: 13.6.20 /BA/Si cherheit/Wartung/ Wartung Zusatz Bei Gasspeic herung/Schneidwekzeu ge @ 2\mod_1203504102 830_78.docx @ 66265 @ @ 1
9 Only use nitrogen for filling pneumatic accumulators - Risk of explosion!
10 When replacing working tools with cutting edges, use suitable tools and gloves!
Pos: 13.6.21 /BA/Si cherheit/Eigenmächtig er Umbau und Ersatztei lherstellung @ 1\mod _1201937705539_78.doc x @ 55745 @ 2 @ 1
4.9 Unauthorised Conversion/Modification and Spare Parts Production
Conversions or modifications of the machine are permitted only with prior consultation with the
manufacturer. Original spare parts and accessories authorised by the manufacturer help to
ensure safety. Use of other parts may void liability for resulting damage.
Pos: 13.6.22 /BA/S icherheit/Unzulässi ge Betriebsweisen @ 11\ mod_1223357699923_78. docx @ 145527 @ 2 @ 1
4.10 Inadmissible Modes of Operation
The operating safety of the delivered machine is guaranteed only when it is used as intended in
compliance with the introductory section "Intended use" of the operating instructions. The limit
values listed in the data charts should not be exceeded under any circumstances.
Pos: 13.6.23 /BA/Si cherheit/Sic herheitshinweise an der Maschi ne @ 1\mod_1201937861961_7 8.docx @ 55783 @ 2 @ 1
4.11 Safety Instructions on the Machine
The safety instructions on the machine warn of residual risks associated with the machine. They
consist of warning pictograms and a work safety symbol. All safety instructions must be
followed. Always keep the safety instructions clean and in clearly legible condition! If any safety
instructions are damaged or missing, request them from your dealer and then put them in the
places provided for them. Where these safety instructions are and what they mean will be
described in the following chapters.
Pos: 13.7 /BA/--- ------------ Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1
To Next Page
Loading...
