Matrix 0850 - Page 8

0850/0850-T1 User Manual
Matrix Machine Tool (Coventry) Limited 8 / 231
Edition: 08/2013
19.4.5 Thread Type 3 ..................................................................................................................................... 121
19.4.6 Thread Type 4 ..................................................................................................................................... 122
19.4.7 Thread Type 5 ..................................................................................................................................... 123
19.4.8 Thread Type 6 ..................................................................................................................................... 124
19.5 Create New Tool ................................................................................................................................. 125
19.6 Grinding Cycle Overview .................................................................................................................... 130
19.6.1 Part Counter (option) ......................................................................................................................... 131
19.7 Dressing Cycle Overview .................................................................................................................... 132
19.8 Setting Cycles Menu ........................................................................................................................... 133
19.9 New Wheel Cycle ............................................................................................................................... 135
19.9.1 Explanation of the Input Parameters ................................................................................................. 136
19.9.2 Procedure for executing the NEW WHEEL setting cycle - if diamond ROLL fitted ............................. 141
19.9.3 Procedure for executing the NEW WHEEL setting cycle - if diamond DISC fitted ............................. 142
19.10 Work Datum Setting Cycle ................................................................................................................. 143
19.10.1 Explanation of the Input Parameters ................................................................................................. 143
19.10.2 Setup method 1 – grind direction from right-to-left ......................................................................... 144
19.10.3 Setup method 2 – grind direction from left-to-right ......................................................................... 144
19.10.4 Procedure for executing the WORK DATUM setting cycle ................................................................ 145
19.11 Barelling function (option) ................................................................................................................. 146
19.11.1 Explanation of the Input Parameters ................................................................................................. 147
19.12 Probe system setup (option) .............................................................................................................. 148
19.12.1 Explanation of the Input Parameters ................................................................................................. 148
19.12.2 Procedure for setting up the probe system ....................................................................................... 149
19.13 Pitch-IN Setting Cycle ......................................................................................................................... 151
19.13.1 Explanation of the Input Parameters ................................................................................................. 151
19.13.2 Pitch-in to workpiece with a pre-cut thread ...................................................................................... 152
19.13.3 Pitch-in to a blank or non-threaded workpiece ................................................................................. 152
19.13.4 Procedure for executing the PITCH-IN setting cycle .......................................................................... 153
19.14 Next Wheel Setting Cycle (option) ..................................................................................................... 154
19.15 Auto Dress Utility Cycle ...................................................................................................................... 155
19.15.1 Explanation of input parameters ....................................................................................................... 156
19.15.2 Procedure for using the Auto Dress cycle .......................................................................................... 157
19.16 Correction Utilities Menu ................................................................................................................... 158
19.17 Lead Correction .................................................................................................................................. 159
19.17.1 Explanation of input parameters ....................................................................................................... 159
19.17.2 Procedure ........................................................................................................................................... 161
19.17.3 Applying lead correction .................................................................................................................... 162
19.18 Taper Correction ................................................................................................................................ 163
19.18.1 Explanation of input parameters ....................................................................................................... 164
19.18.2 Positive Taper Error ............................................................................................................................ 165
19.18.3 Negative Taper Error .......................................................................................................................... 165
19.18.4 Procedure ........................................................................................................................................... 166
19.19 Diameter Correction .......................................................................................................................... 167
19.19.1 Explanation of input parameters ....................................................................................................... 167
19.19.2 Applying diameter correction ............................................................................................................ 168
19.19.3 Procedure ........................................................................................................................................... 168
19.20 Profile Correction ............................................................................................................................... 169
19.20.1 Explanation of input parameters ....................................................................................................... 170
19.20.2 Procedure ........................................................................................................................................... 171
19.21 Barrelling Correction .......................................................................................................................... 172
19.21.1 Procedure ........................................................................................................................................... 172
19.22 Cycle Data - Grind Table ..................................................................................................................... 173
19.22.1 Procedure to edit Grind cycle variables ............................................................................................. 174
19.22.2 Grinding Zones ................................................................................................................................... 175
19.22.3 Explanation of parameters ................................................................................................................. 176