Allied Telesis AT-9724TS Reference Manual

show 802.1x auth_configuration
Purpose Used to display the current configuration of the 802.1x server on the Switch.
Syntax show 802.1x auth_configuration {ports [<portlist> | all]}
Description The show 802.1x command is used to display the current configuration of the 802.1x Port-based and MAC-
based Network Access Control server application on the Switch.
The following details what is displayed:
Authentication Protocol: Radius_Eap – Shows the authentication protocol suite in use between the Switch and
a RADIUS server.
Authentication Mode – Displays the type of authentication mode of the 802.1x function on the Switch.
Authentication may be made by port or by MAC address.
Port number – Shows the physical port number on the Switch.
Capability:Authenticator/None – Shows the capability of 802.1x functions on the port number displayed above.
There are two 802.1x capabilities that can be set on the Switch:Authenticator and None.
AdminCtlDir: Both/In – Shows whether a controlled Port that is unauthorized will exert control over
communication in both receiving and transmitting directions,or just the receiving direction.
OpenCtlDir: Both/In – Shows whether a controlled Port that is unauthorized will exert control over
communication in both receiving and transmitting directions,or just the receiving direction.
Port Control: ForceAuth/ForceUnauth/Auto – Shows the administrative control over the port’s authorization
status. ForceAuth forces the Authenticator of the port to become Authorized. ForceUnauth forces the port to
become Unauthorized.
TxPeriod – Shows the time to wait for a response from a supplicant (user) to send EAP Request/Identity
packets.
SuppTimeout – Shows the time to wait for a response from a supplicant (user) for all EAP packets, except for
the Request/Identity packets.
ServerTimeout – Shows the length of time to wait for a response from a RADIUS server.
MaxReq – Shows the maximum number of times to retry sending packets to the supplicant.
ReAuthenticate: Enabled/Disabled – Shows whether or not to re-authenticate.
Parameters ports <portlist> – Specifies a range of ports.The port list is specified by listing the lowest switch number and the
beginning port number on that switch, separated by a colon.Then the highest switch number, and the highest
port number of the range (also separated by a colon) are specified.The beginning and end of the port list range
are separated by a dash. For example, 1:3 specifies switch number 1, port 3. 2:4 specifies switch number 2, port
4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2,port 4 – in numerical order.
Restrictions Only administrator-level users can issue this command.
170
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g