Allied Telesis AT-9724TS Reference Manual

Example usage:
To configure route redistributions:
AT-9724TS:4# config route redistribute dst ospf src rip
mettype type_1 metric 2
Command: config route redistribute dst ospf src rip mettype
type_1 metric 2
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
delete route redistribute
Purpose Used configure route redistribution settings for the exchange of RIP routes to OSPF routes on the Switch.
Syntax delete route redistribute {dst [rip | ospf] src [rip | static | local | ospf]}
Description This command will delete the route redistribution settings on this switch.
Parameters dst [rip | ospf] – Allows the selection of the protocol on the destination device.The user may choose between
RIP and OSPF.
src [rip | static | local | ospf] – Allows the selection of the protocol on the source device.The user may choose
between RIP, static, local or OSPF.
Restrictions Only administrator-level users can issue this command.
Example usage:
To delete route redistribution settings:
AT-9724TS:4# delete route redistribute dst rip src ospf
Command: delete route redistribute dst rip src ospf
S u c c e s s .
A T - 9 7 2 4 T S : 4 #
show route redistribute
Purpose Used to display the route redistribution on the Switch.
Syntax show route redistribute {dst [rip | ospf] | src [rip | static | local | ospf]}
Description Displays the current route redistribution settings on the Switch.
Parameters src [rip | static | local | ospf] – Allows the selection of the routing protocol on the source device.The user may
choose between RIP, static, local or OSPF.
dst [rip | ospf] – Allows the selection of the routing protocol on the destination device.The user may choose
between RIP and OSPF.
Restrictions None.
Example usage:
To display route redistributions:
AT-9724TS:4# show route redistribute
Command: show route redistribute
Source Protocol Destination Protocol T y p e M e t r i c
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
S T A T I C R I P A l l 1
L O C A L O S P F T y p e - 2 2 0
Total Entries: 2
A T - 9 7 2 4 T S : 4 #
228
Allied Telesyn AT-9724TS High-Density Layer 3 Stackable Gigabit Ethernet Switch • Command Line Interface Reference Manual

Allied Telesis AT-9724TS Specifications

General

MAC address table	16000 entries
Packet buffer memory	2 MB
Maximum data transfer rate	88 Gbit/s
Full duplex	Yes
Dimensions (WxDxH)	440 x 210 x 44 mm
Power requirements	100-240V AC/50-60Hz
Management platform	SNMP, RMON
Networking features	IEEE 802.3 10T Ethernet, IEEE 802.3u 100TX Ethernet, IEEE 802.3ab 1000T Ethernet, IEEE 802.3z 1000X Ethernet
Connectivity technology	Wired
DHCP features	DHCP client
Security algorithms	SSH
Switch type	Managed
Switch layer	L3+
SFP/SFP+ slots quantity	4
Basic switching RJ-45 Ethernet ports quantity	24
Memory type	SDRAM / Flash
Flash memory	16 MB
Internal memory	256 MB
Power consumption (typical)	90 W
Certification	UL 1950 FCC Class A CSA 22.2 No. 950 EN55022 Class A EN 60950 (TUV) EN50082-1 CE
Storage temperature (T-T)	-25 - 55 °C
Operating temperature (T-T)	0 - 40 °C

Weight and Dimensions

Weight	3200 g