AudioCodes Media 800 MSBR

Version 6.6 887 Mediant 800 MSBR
User's Manual 66. Configuration Parameters Reference
Parameter Description
CLI: mlpp-norm-ser-dmn
[MLPPNormalizedServic
eDomain]
‘FFFFFF’, the Resource-Priority header is set to the MLPP Service
Domain obtained from the Precedence IE.
The valid value is 6 hexadecimal digits. The default is ‘000000’.
Note: This parameter is applicable only to the MLPP NI-2 ISDN variant
with CallPriorityMode set to 1.
CLI: mlpp-nwrk-id
[MLPPNetworkIdentifier]
Defines the MLPP network identifier (i.e., International prefix or
Telephone Country Code/TCC) for IP-to-ISDN calls, according to the
UCR 2008 and ITU Q.955 specifications.
The valid range is 1 to 999. The default is 1 (i.e., USA).
The MLPP network identifier is sent in the Facility IE of the ISDN Setup
message. For example:
 MLPPNetworkIdentifier set to default (i.e., USA, 1):
PlaceCall- MLPPNetworkID:0100 MlppServiceDomain:123abc,
MlppPrecLevel:5
Fac(1c): 91 a1 15 02 01 05 02 01 19 30 0d 0a 01 05 0a 01 01 04 05
01 00 12 3a bc
 MLPPNetworkIdentifier set to 490:
PlaceCall- MLPPNetworkID:9004 MlppServiceDomain:123abc,
MlppPrecLevel:5
Fac(1c): 91 a1 15 02 01 0a 02 01 19 30 0d 0a 01 05 0a 01 01 04 05
90 04 12 3a bc
Web: MLPP Default
Service Domain
EMS: Default Service
Domain
CLI: mlpp-dflt-srv-domain
[MLPPDefaultServiceDo
main]
Defines the MLPP default service domain string. If the device receives a
non-MLPP ISDN incoming call (without a Precedence IE), it uses the
parameter (if different than “FFFFFF”) as a Service domain in the SIP
Resource-Priority header in outgoing (Tel-to-IP calls) INVITE
messages. This parameter is used in conjunction with the parameter
SIPDefaultCallPriority.
If MLPPDefaultServiceDomain is set to 'FFFFFF', the device interworks
the non-MLPP ISDN call to non-MLPP SIP call, and the outgoing
INVITE does not contain the Resource-Priority header.
The valid value is a 6 hexadecimal digits. The default is "000000".
Note: This parameter is applicable only to the MLPP NI-2 ISDN variant
with CallPriorityMode set to 1.
Web/EMS: Precedence
Ringing Type
CLI: precedence-ringing
[PrecedenceRingingTyp
e]
Defines the index of the Precedence Ringing tone in the Call Progress
Tones (CPT) file. This tone is used when the parameter
CallPriorityMode is set to 1 and a Precedence call is received from the
IP side.
The valid range is -1 to 16. The default is -1 (i.e., plays standard ringing
tone).
Note: This parameter is applicable only to analog interfaces.
EMS: E911 MLPP
Behavior
CLI: e911-mlpp-bhvr
[E911MLPPBehavior]
Defines the E911 (or Emergency Telecommunication Services/ETS)
MLPP Preemption mode:
 [0] = (Default) Standard Mode - ETS calls have the highest priority
and preempt any MLPP call.
 [1] = Treat as routine mode - ETS calls are handled as routine calls.
Note: This parameter is applicable only to analog interfaces.
CLI: resource-prio-req
[RPRequired]
Determines whether the SIP resource-priority tag is added in the SIP
Require header of the INVITE message for Tel-to-IP calls.

[0] Disable = Excludes the SIP resource-priority tag from the SIP