CallingNameMapTel2Ip_SourcePrefix,
CallingNameMapTel2Ip_CallingNamePrefix,
CallingNameMapTel2Ip_SrcTrunkGroupID,
CallingNameMapTel2Ip_SrcIPGroupID,
CallingNameMapTel2Ip_RemoveFromLeft,
CallingNameMapTel2Ip_RemoveFromRight,
CallingNameMapTel2Ip_LeaveFromRight,
CallingNameMapTel2Ip_Prefix2Add,
CallingNameMapTel2Ip_Suffix2Add;
[ \CallingNameMapTel2Ip ]
Note: For a detailed description of this table, see 'Configuring SIP
Calling Name Manipulation' on page 310.
Destination Phone Number Manipulation for IP-to-Tel Calls Table
Web: Destination Phone
Number Manipulation Table
for IP > Tel Calls
EMS: SIP Manipulations >
Destination IP to Telcom
CLI: configure voip > gw
manipulations
NumberMapIp2Tel2
[NumberMapIP2Tel]
This table parameter manipulates the destination number of IP-to-Tel
calls. The format of this parameter is as follows:
[NumberMapIp2Tel]
FORMAT NumberMapIp2Tel_Index =
NumberMapIp2Tel_DestinationPrefix, NumberMapIp2Tel_SourcePrefix,
NumberMapIp2Tel_SourceAddress, NumberMapIp2Tel_NumberType,
NumberMapIp2Tel_NumberPlan, NumberMapIp2Tel_RemoveFromLeft,
NumberMapIp2Tel_RemoveFromRight,
NumberMapIp2Tel_LeaveFromRight, NumberMapIp2Tel_Prefix2Add,
NumberMapIp2Tel_Suffix2Add,
NumberMapIp2Tel_IsPresentationRestricted;
[\NumberMapIp2Tel]
For example:
NumberMapIp2Tel 0 = 01,034,10.13.77.8,$$,0,$$,2,$$,667,$$;
NumberMapIp2Tel 1 = 10,10,1.1.1.1,255,255,3,0,5,100,$$,255;
Note: For a detailed description of this table, see 'Configuring
Source/Destination Number Manipulation' on page 303.
EMS: Perform Additional
IP2TEL Destination
Manipulation
CLI: prfm-ip-to-tel-dst-map
[PerformAdditionalIP2TEL
DestinationManipulation]
Enables additional destination number manipulation for IP-to-Tel calls.
The additional manipulation is done on the initially manipulated
destination number, and this additional rule is also configured in the
manipulation table (NumberMapIP2Tel parameter). This enables you to
configure only a few manipulation rules for complex number
manipulation requirements (that generally require many rules).
[0] = Disable (default)
[1] = Enable
Destination Phone Number Manipulation for Tel-to-IP Calls Table
Web: Destination Phone
Number Manipulation Table
for Tel > IP Calls
EMS: SIP Manipulations >
Destination Telcom to IPs
CLI: configure voip > gw
manipulations
NumberMapTel2Ip
[NumberMapTel2IP]
This table parameter manipulates the destination number of Tel-to-IP
calls. The format of this parameter is as follows:
[NumberMapTel2Ip]
FORMAT NumberMapTel2Ip_Index =
NumberMapTel2Ip_DestinationPrefix, NumberMapTel2Ip_SourcePrefix,
NumberMapTel2Ip_SourceAddress, NumberMapTel2Ip_NumberType,
NumberMapTel2Ip_NumberPlan, NumberMapTel2Ip_RemoveFromLeft,
NumberMapTel2Ip_RemoveFromRight,
NumberMapTel2Ip_LeaveFromRight, NumberMapTel2Ip_Prefix2Add,
NumberMapTel2Ip_Suffix2Add,
NumberMapTel2Ip_IsPresentationRestricted,
To Next Page
Loading...
