BENSHAW RSi H2 Series - Application Group 1 (AP1); AP1 Parameter List; PID Sleep Mode

PID Control
233
890053-00-02
6.3 Application Group 1 (AP1)
Application Group 1 (AP1) includes additional PID control related parameters and are described
below.
6.3.1 AP1 Parameter List
Code
Name
LCD
Display
Setting Range
Initial Value
Property*
Ref.
00
Jump Code
Jump Code
1–99
20
O
p.74
05
Sleep boost amount
Sleep Bst Set
0.00–Unit Max
0.00
O
p.233
06
Sleep boost speed
Sleep Bst Freq
0.00, Low
Freq– High Freq
60.00
O
p.233
07
PID sleep mode 1 delay time
PID Sleep 1 DT
0.0–6000.0 (sec)
20.0
O
p.233
08
PID sleep mode 1 frequency
PID Sleep1Freq
0.00, Low Freq– High Freq
0.00
O
p.233
09
PID wakeup 1 delay time
PID WakeUp1 DT
0.0–6000.0 (sec)
20.0
O
p.233
10
PID wakeup 1 value
PID WakeUp1Dev
0.00–Unit Band
20.00
O
p.233
11
PID sleep mode 2 delay time
PID Sleep 2 DT
0.0–6000.0 (sec)
20.0
O
p.233
12
PID sleep mode 2 frequency
PID Sleep2Freq
0.00, Low Freq– High Freq
0.00
O
p.233
13
PID wakeup 2 delay time
PID WakeUp2 DT
0.0–6000.0 (sec)
20.0
O
p.233
14
PID wakeup 2 value
PID WakeUp2Dev
0.00–Unit Band
20.00
O
p.233
20
Soft Fill function options
Soft Fill Sel
0
No
0
No
O
p.235
1
Yes
21
Pre- PID
operation frequency
Pre-PID Freq
Low Freq– High Freq
30.00
O
p.235
22
Pre- PID delay time
Pre-PID Delay
0.0–600.0 (sec)
60.0
O
p.235
23
Soft Fill escape value
Soft Fill Set
Unit Min–Unit Max
20.00
O
p.235
24
Soft Fill reference increasing value
Fill Step Set
0.00–Unit Band
2.00
O
p.235
25
Soft Fill reference increasing cycle
Fill Step Time
0–9999 (sec)
20
O
p.235
26
Soft Fill changing amount
Fill Fdb Diff
0.00–Unit Band
0.00
O
p.235
30
Flow Comp function options
Flow Comp Sel
0
No
0
No
O
p.238
1
Yes
31
Max Comp amount
Max Comp Value
0.00–Unit Band
0.00
O
p.238
6.3.2 PID Sleep Mode
With normal PI Control, when operation continues at a frequency lower than the PID operating
conditions, the inverter can enter sleep mode. A boost operation can be performed before sleep to
extend sleep mode. In PID sleep mode, when the PID feedback falls below the PID Wakeup level
and maintains the condition for the time set at AP1-09 (PID WakeUp1 DT), the inverter wakes up
and resumes PID operation.
Two configurations are available for PID sleep mode.
Sleep/Wake Up 1 (AP1-07~AP1-10) and Sleep/Wake Up 2 (AP1-11 ~ AP1-14). Each has settings
for sleep frequency, sleep delay time, wakeup variation, and wakeup delay time. A digital input set
to ’39 (Sleep Wake Chg)’ can be configured to switch between the two configurations.