Cisco D9854 - Page 301

To Next Page

To Previous Page

4021470 Rev D Model D9854 Advanced Program Receiver Installation and Operation Guide B-5

Factory Default Settings, Continued

Video

Audio

Parameter Default

PV Format Auto

SD Format Auto

Tri-Synch (Front Panel only) Disabled

TV A/R 4:3

Convert None

WSS Mode Passthrough

Parameter Default

Stereo/Mono Stereo

AC3 Compression RF Mode

Left (dB) 0

Right (dB) 0

DDP (Front Panel only) Trans

PMT Source AUD1

Digital Out Pref PCM Samples

Main Page

Safety Precautions5
Règles de Sécurité10
Sicherheitsvorkehrungen11
Precauciones de Seguridad12
Precauzioni DI Sicurezza13
Important Safety Instructions14
- Table of Contents21
About this Manual27
Chapter 1 Quick Setup - Read Me First29
- Connecting the Receiver29
- Set up for Network Connection31
- Quick Setup Instructions for RF Acquisition32
- Assigning a Program Channel to a PE (Program Entry)34
- Factory Default Settings35
- ASI out for both Models35
- D9854 Advanced Program Receiver35
- HD-SDI Outputs (SDI Model, with SD/HD-SDI and AES Outputs)36
- MOIP Outputs (Base Model)37
- Setting the DPM Mode38
In this Chapter39
- This Chapter Contains the Following Topics39
Chapter 2 Introduction39
Chapter 3 Installation45
Topic See Page46
- Section a - Rack Installation47
  - General47
  - Installing the D9854 Receiver48
- Section B - Rear Connector Panel50
  - Overview50
- Section C - Connecting the Input/Output Signals52
Chapter 4 Front Panel Operation63
- About the Front Panel64
- Keypad Convention66
- Front Panel Setup69
- Startup Screen70
- Main Menu75
- Status Menu76
- Model D9854 Advanced Program Receiver Installation and Operation Guide76
- Status Menu: General77
- Status Menu: Services79
- Status Menu: TS Input81
- Setup Menu87
- Setup Menu: Admin88
- Setup Menu: TS Input93
- Setup Menu: IP100
- Setup Menu: Services104
- Setup Menu: Common Interface (CI)119
- Setup Menu: Outputs124
- Setup Menu: CA147
- Setup Menu: Alarm/Warning150
- Setup Menu: Noise Cutoffs152
- About Menu155
- Versions Menu157
- Diagnostics Menu160
Chapter 5 Setup and Monitoring167
- Logging on to the Web Interface167
- Web Interface - Summary Screen168
- Tab Pages169
- D9854 Web Interface Environment170
- Viewing the Input and Output Status171
- Viewing the Alarm and Warning Messages173
- Viewing the CA Status174
- Viewing the CI Status176
- Viewing the Input Status177
- Viewing the Output Status180
- Viewing the Services Status182
- Viewing the Audio Status184
- Viewing the Video Status185
- Setting up the TS Input187
- Setting up Custom Tuning Parameters190
- Setting up the Program Entry Configurations191
- Setting up the BISS Mode192
- Configuring the Common Interface (CI) Information193
- Setting up the Common Interface: CI Components195
- Configuring the Transport Stream: TS Output197
- Configuring the Transport Stream: DPM Global200
- Configuring the Transport Stream: DPM ASI/MPEG Details203
- Configuring the Transport Stream: DPM Table Opt204
- Setting up the TS Output: Mpegoip209
- Setting up Cueing Parameters211
- Setting up Cueing: Cue Tones213
- Setting up Services214
- Setting up Services: Audio215
- Setting up Services: Caption217
- Setting up Services: Subtitles218
- Setting up the Video Service221
- Setting up Alarms223
- Setting up Warnings224
- Setting up Muting Threshold Controls225
- Configuring User Settings228
- Viewing the System Status230
- Viewing the Alarm/Warning Status231
- Setting up Backup Restore232
- Viewing Backup Restore Status234
- Setting up Ethernet Ports235
- Viewing Temperatures237
- Setting up SNMP Trap Destinations238
- Viewing Version Information240
- Viewing License Information241
- Viewing the Program Entry Stream Information242
- Viewing PSI Frequency Information243
- Viewing the PSI Channels244
- Viewing the PSI Tables245
- Viewing Alarm/Warning History246
- Viewing Log Messages247
Chapter 6 Service and Maintenance249
- Section a - Front Panel Leds250
  - Introduction250
  - Messages251
- Section B - Power Supply Replacement270
  - Introduction270
Chapter 7 Customer Information271
- Product Support272
- Returning Products274
Appendix A Technical Specifications277
- Section a - L-Band Input and Processing281
- Section B - Video Inputs/Outputs and Processing285
- Section C - Transport Stream Outputs291
- Section D - Control and Management Interfaces292
- Section E - Power and General Specifications294
Appendix B Default Settings297
- Factory Default Settings298
Appendix C Lock Levels309
- D9854 Receiver Lock Levels310
Appendix D Equipment and Accessories323
- Accessory Kits for the D9854 Receiver323
- Accessory Kits for the D9854 Receiver324
Appendix E Compliance325
- Applicable Standards and Notices325
Appendix F Software End User License Agreement327
- End User License Agreement331
- 1.1.1 Available under License332
- Jquery332
- 1.2 Jstracer.js Unknown337
- 1.2.1 Available under License337
- 1.3 Ntp 4.2.4 :P4337
- 1.4.1 Available under License341
- Tokenizer.js341
- 1.5 Zlib 1.2.3 :3342
- 1.5.1 Available under License342

Cisco D9854 - Page 301

Table of Contents

Other manuals for Cisco D9854

Related product manuals