Cisco D9854 User Manual

Name: Cisco D9854
Brand: Cisco
Rating: 5 (1 reviews)

344 pages

To Next Page

To Previous Page

6-22 Model D9854 Advanced Program Receiver Installation and Operation Guide 4021470 Rev D

Section B - Power Supply Replacement

Introduction

Removal and Replacement

There are no user-serviceable parts in the D9854 receiver supply. If the power

supply requires replacement, contact your service provider or Cisco for information

on how to return the unit for repair.

Safety Precautions5
Règles de Sécurité10
Sicherheitsvorkehrungen11
Precauciones de Seguridad12
Precauzioni DI Sicurezza13
Important Safety Instructions14
- Table of Contents21
About this Manual27
Chapter 1 Quick Setup - Read Me First29
- Connecting the Receiver29
- Set up for Network Connection31
- Quick Setup Instructions for RF Acquisition32
- Assigning a Program Channel to a PE (Program Entry)34
- Factory Default Settings35
- ASI out for both Models35
- D9854 Advanced Program Receiver35
- HD-SDI Outputs (SDI Model, with SD/HD-SDI and AES Outputs)36
- MOIP Outputs (Base Model)37
- Setting the DPM Mode38
In this Chapter39
- This Chapter Contains the Following Topics39
Chapter 2 Introduction39
Chapter 3 Installation45
Topic See Page46
- Section a - Rack Installation47
  - General47
  - Installing the D9854 Receiver48
- Section B - Rear Connector Panel50
  - Overview50
- Section C - Connecting the Input/Output Signals52
Chapter 4 Front Panel Operation63
- About the Front Panel64
- Keypad Convention66
- Front Panel Setup69
- Startup Screen70
- Main Menu75
- Status Menu76
- Model D9854 Advanced Program Receiver Installation and Operation Guide76
- Status Menu: General77
- Status Menu: Services79
- Status Menu: TS Input81
- Setup Menu87
- Setup Menu: Admin88
- Setup Menu: TS Input93
- Setup Menu: IP100
- Setup Menu: Services104
- Setup Menu: Common Interface (CI)119
- Setup Menu: Outputs124
- Setup Menu: CA147
- Setup Menu: Alarm/Warning150
- Setup Menu: Noise Cutoffs152
- About Menu155
- Versions Menu157
- Diagnostics Menu160
Chapter 5 Setup and Monitoring167
- Logging on to the Web Interface167
- Web Interface - Summary Screen168
- Tab Pages169
- D9854 Web Interface Environment170
- Viewing the Input and Output Status171
- Viewing the Alarm and Warning Messages173
- Viewing the CA Status174
- Viewing the CI Status176
- Viewing the Input Status177
- Viewing the Output Status180
- Viewing the Services Status182
- Viewing the Audio Status184
- Viewing the Video Status185
- Setting up the TS Input187
- Setting up Custom Tuning Parameters190
- Setting up the Program Entry Configurations191
- Setting up the BISS Mode192
- Configuring the Common Interface (CI) Information193
- Setting up the Common Interface: CI Components195
- Configuring the Transport Stream: TS Output197
- Configuring the Transport Stream: DPM Global200
- Configuring the Transport Stream: DPM ASI/MPEG Details203
- Configuring the Transport Stream: DPM Table Opt204
- Setting up the TS Output: Mpegoip209
- Setting up Cueing Parameters211
- Setting up Cueing: Cue Tones213
- Setting up Services214
- Setting up Services: Audio215
- Setting up Services: Caption217
- Setting up Services: Subtitles218
- Setting up the Video Service221
- Setting up Alarms223
- Setting up Warnings224
- Setting up Muting Threshold Controls225
- Configuring User Settings228
- Viewing the System Status230
- Viewing the Alarm/Warning Status231
- Setting up Backup Restore232
- Viewing Backup Restore Status234
- Setting up Ethernet Ports235
- Viewing Temperatures237
- Setting up SNMP Trap Destinations238
- Viewing Version Information240
- Viewing License Information241
- Viewing the Program Entry Stream Information242
- Viewing PSI Frequency Information243
- Viewing the PSI Channels244
- Viewing the PSI Tables245
- Viewing Alarm/Warning History246
- Viewing Log Messages247
Chapter 6 Service and Maintenance249
- Section a - Front Panel Leds250
  - Introduction250
  - Messages251
- Section B - Power Supply Replacement270
  - Introduction270
Chapter 7 Customer Information271
- Product Support272
- Returning Products274
Appendix A Technical Specifications277
- Section a - L-Band Input and Processing281
- Section B - Video Inputs/Outputs and Processing285
- Section C - Transport Stream Outputs291
- Section D - Control and Management Interfaces292
- Section E - Power and General Specifications294
Appendix B Default Settings297
- Factory Default Settings298
Appendix C Lock Levels309
- D9854 Receiver Lock Levels310
Appendix D Equipment and Accessories323
- Accessory Kits for the D9854 Receiver323
- Accessory Kits for the D9854 Receiver324
Appendix E Compliance325
- Applicable Standards and Notices325
Appendix F Software End User License Agreement327
- End User License Agreement331
- 1.1.1 Available under License332
- Jquery332
- 1.2 Jstracer.js Unknown337
- 1.2.1 Available under License337
- 1.3 Ntp 4.2.4 :P4337
- 1.4.1 Available under License341
- Tokenizer.js341
- 1.5 Zlib 1.2.3 :3342
- 1.5.1 Available under License342

Other manuals for Cisco D9854

Installation And Configuration Guide440 pages

Questions and Answers:

Need help?

Do you have a question about the Cisco D9854 and is the answer not in the manual?

Cisco D9854 Specifications

General

Model	D9854
Category	Receiver
Output	ASI, IP
Decoding	MPEG-2
Conditional Access	BISS
Receiver Type	Professional IRD
解密	DVB-CSA, BISS, AES
Input Frequency Range	950 MHz to 2150 MHz
Modulation Formats	QPSK, 8PSK
Symbol Rate	1 to 45 Msps
Power Supply	100-240 VAC, 50/60 Hz
Power Consumption	40W (typical)
Operating Temperature	0°C