R-1
Revision History
A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
Cat. No. I515-E1-3
Revision code
The following table outlines the changes made to the manual during each revision. Page numbers refer to the
previous version.
Revision code Date Revised content
1 August 1996
Original production
2 April
1997
Page
1-2:
Inverter model list updated. “Enclosed wall-
mounted type” replaced with “NEMA1 type.”
Page 1-4: Low noise and harmonic countermeasure
information clarified.
Page 2-4: Dimensions added for the new models.
Page 2-5: “Enclosed Wall-mounted Type” replaced with
“NEMA1 Type.”
Page 2-7: Terminals U, V, and W replaced with T1 (U),
T2 (V), and T3 (W) respectively.
Pages 2-10, 2-11: Terminals and connections changed
for the 200-V Class and 400-V Class tables. New models
reflected.
Page 2-12: Names for the three-phase terminals
changed.
Page 2-13: Names for the three-phase terminals
changed. Notes added. New models reflected.
Pages 2-14, 2-15: Terminal names changed and new
models added. New wire sizes and tightening torque
added.
Pages 2-16 to 2-20:
Information for
Wiring on the Input
Side of Main Circuit
and
Wiring on the Output Side of
Main Circuit
changed.
Page 2-22: Second harmonic frequency corrected.
Information in
Causes of Harmonics Generation
cor-
rected at the bottom of the page.
Page 2-23: Last sentence of
DC/AC Reactors
corrected.
Note added.
Pages 2-24, 2-25: Terminal names changed. New model
information reflected.
Page 2-26: Inverter models added to the input trans-
former table.
Page 2-27: New model information reflected. Information
on connecting Braking Units in parallel added. Informa-
tion removed from
Wire Size and Solderless Terminals
at
the bottom of the page.
Pages 3-3, 3-9: Terminal names changed.
Page 3-44: Note added.
Page 3-58: New model information reflected in the table.
Page 3-72: Notes added.
Pages 4-2, 4-8: Terminal names changed.
Pages 4-3, 4-4: Cause and action for the heat sink over-
heat and Inverter overload added to.
Page 4-12: Inverter overload information added.
Pages 5-2, 5-3: Specifications completely updated.
Pages 5-5, 5-9, 5-10: “Control Unit” corrected to “Braking
Unit.”
Pages 5-9, 5-10: New models added.
Pages 5-15, 5-18: Noise Filter models added.
Page 6-5: New models added.
Page 6-13: Note added.
3 April
2000
Preliminary
pages:
Order changed and safety information added.
Pages 1-6, 2-33, 3-2, 3-5, 3-7, 3-16, 3-20, 3-21, 3-22, 3-38 to 3-50, 3-52, 3-56, 3-69,
3-71, 3-74, 3-80, 3-84, 5-1
1:
Notes changed or added.
Page 1-6, 3-2: Explanation for “Operation Mode Selection Key” changed.
Page 1-7:
Information on new functions added.
Pages 2-6, 2-15, 3-20, 3-31, 3-55, 5-5:
Graphics changed or added.
Pages 2-7, 3-2, 4-13:
“Cautions and W
arnings” information changed.
Page 2-9:
Information on wiring changed.
Pages 2-14, 3-5, 3-13, 3-21, 3-31, 3-38 to 3-50, 3-56, 3-62, 3-72, 3-74, 5-1
1, 5-13, 6-5
to 6-8:
Changes made to tables.
Pages 2-20 to 2-22, 5-17 to 5-19:
Major changes.
Page 2-24:
Changes made to information on cable length. Information on single-phase
motors added.
Page 3-8:
Information on operation modes added after table.
Page 3-23, 4-2:
Information added to introduction.
Page 3-58:
Setting range for n030 changed.
Page 3-61:
Setting range for n039 changed.
Page 3-65: Information for external baseblock command changed.
Page 3-66:
Information on PID control added.
Page 3-75:
Default setting for n052 changed.
Page 3-76:
Setting range for n053 changed.
Page 3-83:
“Motor Rated Slip” changed to “Slip Compensation Gain.”
Page 3-84:
Information for n1
12, n113, and n1
14 changed.
Page 4-4:
Information on connection error added.
Page 4-12:
Information added.
Pages 5-3, 5-4:
“IP00” changed to “IP10.”
Index:
Index removed.
To Next Page
Loading...
Need help?
General