17.2 Operation of Digital Operator
17.2.2 Operation of Utility Functions
17-30
INDEXER Alarm History Display (FnB0D)
This function displays the history of alarms that have occurred at the SERVOPACK and
INDEXER Module.
Preparation
None
Operating Procedure
6
Press the key to return to the Utility Function
Mode main menu.
* If the key is pressed in an operation prohibited state, “Error.” is displayed for approximately 2 seconds and then the
display returns to the FnB0C operation screen. In this case, make the setting again by referring to
Preparation.
Step Display after Operation Keys Operation
1
Press the key to open the Utility Function
Mode main menu, and move the cursor with the
keys to select FnB0D.
2
Press the key to view the alarm history.
If no alarms occur, “NONE” is displayed.
3
Use the keys to scroll the alarm history.
4
Press the key to return to the Utility Function
Mode main menu.
To clear the alarm history, execute the Reset INDEXER Alarm (FnB0C) utility function with
Mode set to ALM History (clear alarm history). The alarm history is not cleared when you
reset an alarm (Mode = ALM state) or when the control power supply to the SERVOPACK is
turned OFF. Refer to the following section for the procedure.
INDEXER Alarm Reset (FnB0C) on page 17-29
Continued from previous page.
Step Display after Operation Keys Operation
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧮㧜㧮ޓ㧼㨞㨙ޓ㧵㨚㨕㨠
㧲㨚㧮㧜㧯ޓ㧭㧸㧹ޓ㧾㨑㨟㨑㨠
㧲㨚㧮㧜㧰ޓ㧵㨚㨐㨑㨤㨑㨞ޓ㧭㧸㧹
㧲㨚㧜㧜㧜ޓ㧭㨘㨙ޓ㧴㨕㨟㨠㨛㨞㨥
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧮㧜㧯ޓ㧭㧸㧹ޓ㧾㨑㨟㨑㨠
㧲㨚㧮㧜㧰ޓ㧵㨚㨐㨑㨤㨑㨞ޓ㧭㧸㧹
㧲㨚㧜㧜㧜ޓ㧭㨘㨙ޓ㧴㨕㨟㨠㨛㨞㨥
㧲㨚㧜㧜㧞ޓ㧶㧻㧳
㧮㧮ޓޓޓޓ㧙㧭㧸㧹ޓ㨀㨞㨍㨏㨑㧙
㧭㧸㧹㧜㧩㧭㧚㧲㧝㧜
㧭㧸㧹㧝㧩㧱㧝㧥㧭
㧭㧸㧹㧞㧩㧺㧻㧺㧱
㧭㧸㧹㧟㧩㧺㧻㧺㧱
㧮㧮ޓޓޓޓ㧙㧭㧸㧹ޓ㨀㨞㨍㨏㨑㧙
㧭㧸㧹㧜㧩㧭㧚㧲㧝㧜
㧭㧸㧹㧝㧩㧱㧝㧥㧭
㧭㧸㧹㧞㧩㧺㧻㧺㧱
㧭㧸㧹㧟㧩㧺㧻㧺㧱
㧮㧮ޓޓޓޓ㧙㧭㧸㧹ޓ㨀㨞㨍㨏㨑㧙
㧭㧸㧹㧝㧩㧱㧝㧥㧭
㧭㧸㧹㧞㧩㧺㧻㧺㧱
㧭㧸㧹㧟㧩㧺㧻㧺㧱
㧭㧸㧹㧠㧩㧺㧻㧺㧱
㧮㧮ޓޓޓޓ㧙㧭㧸㧹ޓ㨀㨞㨍㨏㨑㧙
㧭㧸㧹㧢㧩㧺㧻㧺㧱
㧭㧸㧹㧣㧩㧺㧻㧺㧱
㧭㧸㧹㧤㧩㧺㧻㧺㧱
㧭㧸㧹㧥㧩㧺㧻㧺㧱
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧮㧜㧯ޓ㧭㧸㧹ޓ㧾㨑㨟㨑㨠
㧲㨚㧮㧜㧰ޓ㧵㨚㨐㨑㨤㨑㨞ޓ㧭㧸㧹
㧲㨚㧜㧜㧜ޓ㧭㨘㨙ޓ㧴㨕㨟㨠㨛㨞㨥
㧲㨚㧜㧜㧞ޓ㧶㧻㧳
To Next Page
Loading...
