ABB RED650 - Page 693

Name Function
block
SPA
address
Description
SELECTOpen=00,
SELECTClose=01, so on.
SCSWI26 1 I 5705 SPA parameters for select (Open/
Close) command
SELECTOpen=00,
SELECTClose=01, so on.
SCSWI27 1 I 5729 SPA parameters for select (Open/
Close) command
SELECTOpen=00,
SELECTClose=01, so on.
SCSWI28 1 I 5753 SPA parameters for select (Open/
Close) command
SELECTOpen=00,
SELECTClose=01, so on.
SCSWI29 1 I 5777 SPA parameters for select (Open/
Close) command
SELECTOpen=00,
SELECTClose=01, so on.
SCSWI30 1 I 5801 SPA parameters for select (Open/
Close) command
SELECTOpen=00,
SELECTClose=01, so on.
SCSWI31 1 I 5825 SPA parameters for select (Open/
Close) command
SELECTOpen=00,
SELECTClose=01, so on.
SCSWI32 1 I 5849 SPA parameters for select (Open/
Close) command
ExcOpen=00,
ExcClose=01,
ExcOpen+ILO=10,
ExcClose+ILO=11,
ExcOpen+SCO=20,
ExcClose+SCO=21,
ExcOpen+ILO+SCO=30,
ExcClose+ILO+SCO=31
SCSWI01 1 I 5106 SPA parameters for operate
(Open/Close) command
Note: Send select command
before operate command
ExcOpen=00,
ExcClose=01, so on.
SCSWI02 1 I 5130 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI02 1 I 5152 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI04 1 I 5177 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI05 1 I 5201 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI06 1 I 5225 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI07 1 I 5249 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI08 1 I 5274 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI09 1 I 5298 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI10 1 I 5322 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI11 1 I 5346 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI12 1 I 5370 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI13 1 I 5394 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI14 1 I 5418 SPA parameters for operate
(Open/Close) command
ExcOpen=00,
ExcClose=01, so on.
SCSWI15 1 I 5442 SPA parameters for operate
(Open/Close) command
Table continues on next page
1MRK 505 394-UEN A Section 18
Station communication
Line differential protection RED650 2.2 IEC 687
Technical manual