What to do if USB memory is not recognized by Autonics krn100 Measuring Instruments?
If the USB memory is not recognized by the Autonics Measuring Instruments KRN100, ensure that the USB memory's file system is formatted as FAT16 or FAT32. Also, if the USB memory has multiple partitions, the KRN100 will only recognize the first partition.
How to troubleshoot incorrect sensor input value on Autonics Measuring Instruments?
If the sensor input value is incorrect on the Autonics Measuring Instruments KRN100, verify that the sensor input settings are correct in the INPUT SETUP. Also, turn off the power, remove the input cards, and check the jumper pin settings according to the input specification.
How to fix Ethernet connection issues with Autonics krn100 Measuring Instruments?
If you cannot connect communication by Ethernet on Autonics Measuring Instruments KRN100, you should check the communication line connection and reset it as described in ‘8.4 COMMUNICATION SETUP (Communication setting).’
What to do if RS485 communication fails on Autonics Measuring Instruments?
If you cannot connect communication via RS485 communication on Autonics Measuring Instruments KRN100, check that the communication line’s A and B signal polarity is connected correctly. Then, reset it as described in ‘8.4 COMMUNICATION SETUP (Communication setting).’
Why is Autonics krn100 recording old data?
If the Autonics Measuring Instruments KRN100 records former digital data instead of the current time's data, it means the record memory status icon ( or ) is active, indicating that it's recording former digital data. To cancel this, pause and restart the recording. Also, adjust the record settings for proper operation.
How to correct date and time on Autonics krn100 Measuring Instruments?
If the displayed date and time are incorrect on the Autonics Measuring Instruments KRN100, reset the date and time. Note that the KRN100 has a date and time error margin of ±2 minutes per year and is usable until the year 2100.
Why is the printout blurry on Autonics Measuring Instruments?
If, in graph mode, the printout for lines and letters is unclear and spread on the Autonics Measuring Instruments KRN100, replace the ink cartridge.
What does the red star on Autonics Measuring Instruments mean?
If the recording paper's terminal mark, a red star shape, is displayed on the Autonics Measuring Instruments KRN100, the recording paper should be replaced. This indicates that only 330mm of recording paper is left.
How to troubleshoot a blank LCD screen on Autonics Measuring Instruments?
If the Autonics Measuring Instruments KRN100 does not display anything on the LCD screen and does not operate when powered on, check the power supply and ensure the power connector is connected correctly.
What to do if Autonics Measuring Instruments freezes on boot screen?
If the Autonics Measuring Instruments KRN100 does not change from the booting screen to the normal operation screen after being powered on, the SD card inside the KRN100 may have a problem. Please contact our service center.
Details the key features and capabilities of the KRN100 recorder.
Lists the included components and separately sold accessories for the KRN100.
Provides details on how to order the KRN100 recorder and its configurations.
Identifies and describes the various parts and components of the KRN100 unit.
Presents the technical specifications for the KRN100 recorder unit.
Details the specifications and types of input/output cards available for the KRN100.
Outlines the input specifications and measurement ranges for various sensors.
Provides the physical dimensions of the KRN100 unit.
Specifies the required panel dimensions for mounting the KRN100.
Illustrates the dimensions and design of the mounting bracket.
Details the rear view of the KRN100 and the function of each slot.
Illustrates the connection diagrams for various I/O cards used with the KRN100.
Provides guidelines for selecting an appropriate installation location for the KRN100.
Describes the process of physically installing the KRN100 unit.
Details the installation process for the USB to Serial driver.
Describes the screens displayed during the KRN100's initial power-on sequence.
Explains the division of the KRN100's screen into status and measurement display areas.
Details how the KRN100 displays measuring values in various modes.
Covers special functions for recording, such as start/stop and manual feed.
Outlines the order and navigation for setting the KRN100's parameters.
Details how to configure input specifications, scales, and error correction.
Covers configuring alarm types, hysteresis, delays, and output methods.
Explains how to set up digital input functions and operation status.
Details parameters for RS485, Ethernet, and USB communication setup.
Covers settings for record mode, speed, language, and paper handling.
Allows configuration of system parameters like date, time, and backlight.
Explains how to set up scheduled recording based on time and period.
Covers managing parameter files, memory status, and USB data transfer.
Details user management, password settings, and firmware upgrades.
Describes how to back up data, manage lists, and select print modes.
Introduces DAQMaster as an integrated device management program.
Lists the key features and capabilities of the DAQMaster software.
Highlights specific KRN100 functions available when communicating with DAQMaster.
Provides step-by-step instructions for replacing the ink cartridge.
Details the procedure for replacing the recording paper roll.
Lists common error messages and their corresponding troubleshooting steps.
General| Brand | Autonics |
|---|---|
| Model | krn100 series |
| Category | Measuring Instruments |
| Language | English |
To Next Page
