Autonics krn100 series User Manual

Table of Contents
© Copyright Reserved Autonics Co., Ltd. ix
8.4.2 RS485 Port (Use RS485 communication) ................................................. 90
8.4.3 Baud Rate (Baud rate) ............................................................................... 90
8.4.4 Parity Bit (Communication parity bit) .......................................................... 91
8.4.5 Stop Bit(Communication stop bit) .............................................................. 91
8.4.6 Termination Set (Terminating resistance) ................................................... 91
8.4.7 Response Wait Time (Communication response wait time) ...................... 92
8.4.8 Protocol (Communication protocol) ............................................................ 92
8.4.9 RS485 Com Write (RS485 communication write) ...................................... 92
8.4.10 Ethernet Port (Use Ethernet communication) ............................................ 93
8.4.11 IP Address (IP address) ............................................................................. 95
8.4.12 Subnet Mask (Subnet Mask) ...................................................................... 95
8.4.13 Default Gateway (Default gateway) ........................................................... 95
8.4.14 Ethernet Com Write (Ethernet communication write) ................................. 96
8.4.15 USB Device Port (Use USB communication) ............................................. 96
8.4.16 USB Com Write (USB communication write) ............................................. 96
8.5 RECORD SETUP (Record setting) .................................................................. 97
8.5.1 Record Mode (Recode mode) .................................................................... 98
8.5.2 Digital Print type(1 line record channel during numeric recording) ............ 99
8.5.3 Standard Speed (Standard record speed) ............................................... 100
8.5.4 Option Speed (Option record speed) ....................................................... 100
8.5.5 Memo Period (Digital memo period) ........................................................ 101
8.5.6 Divide Zone (Record zone division) ......................................................... 103
8.5.7 Standard Period (Standard record period) ............................................... 104
8.5.8 Option Period (Option record period) ....................................................... 104
8.5.9 Listing Language (Language for list output) ............................................. 105
8.5.10 Alarm Speed (Alarm record speed) ......................................................... 106
8.5.11 Power On Status (Record status when power ON) ................................. 106
8.5.12 Run Status (List printing at start recording) ............................................. 107
8.5.13 List Out Option (List record option) .......................................................... 108
8.5.14 Zone Dot Line Distance (Dot line for zone division) ................................. 109
8.5.15 CH Print Distance (Record interval for each channel graph) ................... 109
8.5.16 Start Line Print (Start line when starting record) ...................................... 110
8.5.17 Range Print Time (Input range record period) ......................................... 110
8.5.18 PenX(color) ON Time (Ink cartridge point delay time) ............................. 111
8.6 SYSTEM SETUP (System setting) .................................................................. 112
8.6.1 Device Name (Device name) ................................................................... 112
8.6.2 Date/Time (Date/Time) ............................................................................. 113
8.6.3 Date Type (Date type) .............................................................................. 113
8.6.4 Summer Time (Summer time) .................................................................. 113
8.6.5 Summer Time Period (Summer time period) ........................................... 114
8.6.6 Alarm Sound (Alarm sound) ..................................................................... 114
8.6.7 Sampling Rate (Sampling period) ............................................................ 114
8.6.8 Log Speed (Save period) ......................................................................... 115
8.6.9 Backlight (LCD backlight brightness) ....................................................... 115
8.6.10 Backlight On/Off (LCD backlight ON method) .......................................... 115
8.7 RESERVATION SETUP (Reservation setting) ................................................ 116
8.7.1 Reservation Type (Reservation record) ................................................... 116
8.7.2 Reservation Period (Reservation record period) ...................................... 117
8.7.3 Reservation Time (Reservation record time) ........................................... 118
8.8 FILE/MEMORY SETUP(File/Memory setting) ................................................. 119

Autonics krn100 series Specifications

General

Brand	Autonics
Model	krn100 series
Category	Measuring Instruments
Language	English