Comtec CDM-840 - Page 11

CDM-840 Remote Router MN-CDM840 / CD-CDM840
Table of Contents Revision 3
vii
6.3.3.5 Configuration | dSCPC (Dynamic Single Carrier per Channel) ........................................ 6–64
6.3.4 Status Pages ............................................................................................................................ 6–66
6.3.4.1 Status | Statistics Pages .................................................................................................. 6–66
6.3.4.1.1 Status | Statistics | Traffic ........................................................................................ 6–66
6.3.4.1.2 Status | Statistics | Network / Router ...................................................................... 6–68
6.3.4.1.3 Status | Statistics | Compression.............................................................................. 6–69
6.3.4.1.4 Status | Statistics | QoS ............................................................................................ 6–70
6.3.4.1.4.1 Page Functionality Common for all QoS Control Modes ................................... 6–71
6.3.4.1.4.2 Page Functionality Specific to Active QoS Control Mode .................................. 6–72
6.3.4.1.5 Status | Statistics | E1 Pages (CDM-840 only) .......................................................... 6–73
6.3.4.1.5.1 Status | Statistics | E1 | Transmit ...................................................................... 6–73
6.3.4.1.5.2 Status | Statistics | E1 | Receive........................................................................ 6–74
6.3.4.1.6 Status | Statistics | Trending (CDM-840 only) .......................................................... 6–76
6.3.4.2 Status | Monitor Pages ................................................................................................... 6–78
6.3.4.2.1 Status | Monitor | Events ......................................................................................... 6–78
6.3.4.2.2 Status | Monitor | Alarms ........................................................................................ 6–79
6.3.5 Utility Pages ............................................................................................................................ 6–81
6.3.5.1 Utility | Utility ................................................................................................................. 6–81
6.3.5.2 Utility | Carrier ID ............................................................................................................ 6–84
6.3.5.3 Utility | Reboot ............................................................................................................... 6–85
CHAPTER 7. SERIAL-BASED REMOTE PRODUCT MANAGEMENT ............................... 7–1
7.1 Overview ............................................................................................................................ 7–1
7.2 Remote Commands and Queries Overview .......................................................................... 7–3
7.2.1 Basic Protocol ........................................................................................................................... 7–3
7.2.2 Packet Structure ....................................................................................................................... 7–4
7.2.2.1 Start of Packet ................................................................................................................... 7–5
7.2.2.2 Target Address .................................................................................................................. 7–5
7.2.2.4 Instruction Code ................................................................................................................ 7–5
7.2.2.5 Instruction Code Qualifier .................................................................................................
7–5
7.2.2.5.1 Controller-to-Target Instruction Code Qualifiers ....................................................... 7–6
7.2.2.5.2 Target-to-Controller Instruction Code Qualifiers ....................................................... 7–6
7.2.2.6 Optional Message Arguments ........................................................................................... 7–7
7.2.2.7 End of Packet .................................................................................................................... 7–8
7.3 Remote Commands and Queries ......................................................................................... 7–9
7.3.1 Table Indexes ............................................................................................................................ 7–9
7.3.2 Transmit (Tx) Parameters Commands and Queries................................................................ 7–12
7.3.3 Receive (Rx) Parameters Commands and Queries ................................................................. 7–14
7.3.4 Demodulator Status Commands and Queries ........................................................................ 7–16
7.3.5 Transmit (Tx) BERT Command or Query ................................................................................. 7–17
7.3.6 Receive (Rx) BERT Command or Query .................................................................................. 7–17
7.3.7 BUC (Block Up Converter) Parameters Commands and Queries ........................................... 7–17
7.3.8 LNB (Low-Noise Block Down Converter) Parameters Commands and Queries ..................... 7–21
7.3.9 Unit Parameters Commands and Queries .............................................................................. 7–22