15
Originals
■ Size and weight
The following sizes and weights of originals are
usable:
When using the glass platen
When using the optional auto document feeder
• Do not mix originals of different sizes for the auto
document feeder.
• You can place up to approximately 50 sheets of orig-
inals (when using originals of 80 g/m
2
[21-lb bond] or
less) in the auto document feeder at the same time.
• If an original is excessively wrinkled, curled, or creased,
flatten it thoroughly so that the entire original is
securely placed on the glass platen. Areas that come
off from the glass platen may be printed in black.
• If ink or correction fluid is used on an original, thor-
oughly dry it before placement. Failure to do so may
contaminate the glass platen, and this impairs
proper printing.
■ Direction of original
Each direction of an original is referred to as follows in
this guide:
• When placing an original on the glass platen:
The side that faces the reference position (H sym-
bol) is referred to as the “top”.
• When placing an original on the optional auto docu-
ment feeder:
The leading edge in the feeding direction is referred
to as the “top”.
Printing papers
• If you use papers outside the specifications of this
machine, RISO does not assure the paper feeding
and printing performance with these papers.
■ Paper size
• The following sizes of paper are usable
*
:
100 mm × 148 mm to 320 mm × 432 mm
(3 15/16 inches × 5 13/16 inches to
12 19/32 inches × 17 inches)
*
When the optional Wide Stacking Tray is installed,
papers of sizes up to 340 mm × 555 mm
(13 3/8 inches × 21 27/32 inches) are usable after set-
ting [Custom Paper Entry] (A 126). Depending on the
paper type and paper size, papers may not be aligned
properly.
• This machine detects the following papers as stan-
dard size paper.
SF9490
Size 50 mm × 90 mm to 310 mm × 432 mm
(1 31/32 inches × 3 17/32 inches to
12 7/32 inches × 17 inches)
Weight 10 kg (22 lb) at maximum
Size 100 mm × 148 mm to 300 mm × 432 mm
(3 15/16 inches × 5 13/16 inches to
11 13/16 inches × 17 inches)
Weight Single-sided transfer:
50 g/m
2
to 128 g/m
2
(13-lb bond to 34-lb bond)
Double-sided transfer:
52 g/m
2
to 105 g/m
2
(14-lb bond to 28-lb bond)
BThe following originals cannot be used in
the auto document feeder. Place the origi-
nal on the glass platen.
CPatched original
CExcessively wrinkled, curled, or creased
original
COriginal with sticky areas or holes
CTorn original or deckle-edged original
CChemically treated original (such as
thermal or carbon paper)
CTransparent original (such as OHP films
or tracing paper)
COriginal with correction fluid or glue
CExtremely thin original
(less than 50 g/m
2
[13-lb bond])
CExtremely thick original
(greater than 128 g/m
2
[34-lb bond])
COriginal with slippery surface (such as
art or coated paper)
COriginal with glossy surfaces
COriginal with staples or clips
BPlease note that even with paper of a
size and weight that conforms to the
specifications of this machine, this
machine may not feed the paper
depending on the paper type, environ-
mental conditions, and storage condi-
tions. For more information, consult
your dealer or authorized service repre-
sentative.
Ledgerp 11 inches × 17 inches
Legalp 8 1/2 inches × 14 inches
Letterp 8 1/2 inches × 11 inches
Lettern 11 inches × 8 1/2 inches
To Next Page
Loading...
