SATO s86ex - Page 352

344
16) RFID setting status request
Returns the current RFID setting status.
(1) Command SOH (01H) + RB
(2) Return status format
・In normal mode (RFID disabled)
[STX] + RFID operation mode number + [ETX]
STX
RFID operation mode number
ETX
・In RFID Setting
[STX] + RFID operation mode number + Extended status Field length + Extended status field part + [ETX]
STX
RFID operation
mode number
Extended status
Field length
Extended status field part
ETX
(The mode number set by <RA> command will be set to the second byte.)
(3) Return status list
Detailed Return Status Configuration at the RFID Setting.
The return status at the RFID setting is extended after the RFID operation mode number.
No.
Item
Content (Binary)
No of bytes
-
STX(02H)
Start code
1
1
RFID operation
mode number
02H : RFID enabled mode
1
2
Extended status
Field length
The following size of the status field indicated by 4 digits decimal
code consists of the number from “0” (30H) to “9” (39H).
(Unit: byte)
4
3
Extended status
Field part
Refer to the table of the status field part details for details.
Variable
-
ETX(03H)
End code
1
Status field part details (Variable size)
The information field at the RFID setting. Information is delimited by comma, and type of subsequent data is
identified by the identifier.
No.
Item
Identifier
Format of data part
1
RFID life counter
"Lc:"
4CH,63H,3AH
"Number of success", "Number of failure", "Total number",
The decimal number consists of maximum 6 digits x 3 item of '0'(30H)
to '9'(39H) and delimited by comma.
2
RFID
counter
"Rc:"
52H,63H,3AH
"Number of success", "Number of failure", "Total number",
The decimal number consists of maximum 6 digits x 3 item of '0'(30H)
to '9'(39H) and delimited by comma.
3
Number of retry
”Ec:”
45H,63H,3AH
Return the number of retry that is set
0(30H) to 9(39H) decimal number delimited by comma.
4
Print at command
error
”Ce:”
43H,65H,3AH
When the error occurs in the command contained in the RFID item,
return the reply whether or not to print.
0 (30H) : Don't print
1 (31H) : Print delimited by comma
5
Tag offset value
”To:”
54H,6FH,3AH
Return the tag offset value.
The decimal number consists of 3 digits of '0'(30H) to '9'(39H) and
delimited by comma.
6
Antenna power
value
(at writing)
”Pw:”
50H,77H,3AH
Return the radio output power value. The decimal number consists of
3 digits of '0'(30H) to '9'(39H) and delimited by comma.
The dBm can be acquired by dividing this value with 10.
7
Antenna power
value
(at reading)
”Pr:”
50H,72H,3AH
Return the radio output power value. The decimal number consists of
3 digits of '0'(30H) to '9'(39H) and delimit by comma.
The dBm can be acquired by dividing this value with 10.
8
Tag type setting
"Ps:"
50H,73H,3AH
Return the tag type.
With this specification, only "4: Gen2" is returned.
9
EPC code length
"Tb:"
54H,62H,3AH
Return the EPC code length when EPC1 is selected.
With this specification, only "0(30h): 96bit" is returned.
10
Timeout
"Mr:"
4DH,72H,3AH
Return the timeout time in the module in the range of 0(30H) to
7(37H). Change the setting of timeout/number of retry in the
module.
Specified
number
0
1
2
3
4
5
6
7
(msec)
50
100
200
500
1000
1500
2000
4000
11
Tag error recovery
”Ed:”
45H,64H,3AH
Return the recovery method at a tag error.
0(30H) : RETRY mode
1(31H) : RELEASE mode
12
Slash printing at
tag error
”Es:”
45H,73H,3AH
Return the setting of slash printing at a tag error.
0(30H) : No slash printing
1(31H) : Slash printing
STX (HEX 02H)
ETX (HEX 03H)
(Total 3 bytes～)