Azbil MagneW FLEX+/PLUS+ MGG10C

Questions and Answers

A
Allison JohnsonAug 21, 2025
What to do if output exceeds 100% on Azbil MagneW FLEX+/PLUS+ MGG10C?
- J
  Julie WrightAug 21, 2025
  If the output exceeds 100% on your Azbil Media Converter, verify that the set range, span and zero point are correctly adjusted. Also, ensure that the converter is correctly calibrated.
S
sarahfuentesSep 4, 2025
What to do if Azbil MagneW FLEX+/PLUS+ MGG10C Media Converter pulse width is too large?
- M
  Marc WalterSep 4, 2025
  If the pulse width is too large on your Azbil Media Converter, check the pulse width, pulse weight, and span setting.
K
Kenneth DrakeSep 2, 2025
What to do if EX check error (Excitation circuit is open) on Azbil MagneW FLEX+/PLUS+ MGG10C?
- M
  Mark PerkinsSep 2, 2025
  If you encounter an EX check error (Excitation circuit is open) on your Azbil Media Converter, check the connection of terminal/wiring of X and Y. Verify if the resistance of coil is less than 50 W by checking between X and Y terminal of a detector. Cycle power.
G
garciamariaSep 1, 2025
Why Azbil MagneW FLEX+/PLUS+ MGG10C Media Converter has no display after power on?
- J
  Jeffrey LloydSep 1, 2025
  If there is no display after powering on your Azbil Media Converter, check the converter power supply specification and ensure that the power supply being supplied meets these requirements. Also, make sure the ambient temperature is not below -25 °C (13 °F).
W
Wayne WilliamsAug 30, 2025
What to do if output remains 0% on Azbil MagneW FLEX+/PLUS+ MGG10C?
- M
  Matthew Cantu DDSAug 31, 2025
  If the output remains 0% on your Azbil Media Converter, the pipe may be empty, so use the empty detection function to check. Verify that the signal cable is correctly connected and that the valves are open on the upper and lower sides. Also, verify that the span is set correctly, the converter is set to the constant current mode, and the flow rate is not in the low flow cutoff range.
M
Mary FernandezAug 29, 2025
What to do if output fluctuates excessively on Azbil MagneW FLEX+/PLUS+ MGG10C?
- P
  Peter JacksonAug 29, 2025
  If the output fluctuates excessively beyond the estimated flow rate range on your Azbil Media Converter, verify that both the detector and the converter are properly grounded. Ensure that the damping time constant is set correctly; if not, set an appropriate damping time constant. Finally, clean the electrodes.
E
Elizabeth ChavezAug 27, 2025
What to do if communication cannot be done with Azbil MagneW FLEX+/PLUS+ MGG10C?
- P
  priceaaronAug 27, 2025
  If communication cannot be done with your Azbil Media Converter, check the switch position (refer to Figure 2-15), ensure the wiring is properly completed, and check if the SFC is properly connected. Also, verify if the S/W version of the SFC is Ver.7.0 or later and if the HART communicator is 375, ensuring the DD file is downloaded.
A
Anita MitchellAug 26, 2025
What to do if pulse output is too large or too small on Azbil MagneW FLEX+/PLUS+ MGG10C?
- M
  Michael BarreraAug 26, 2025
  If the pulse output is too large or too small on your Azbil Media Converter, verify if the pulse weight and width are set correctly. Also, verify the converter is correctly calibrated, the pulse counter is proper, and the dropout value is correctly set between 0 and 10%.
A
Amanda ButlerAug 25, 2025
What to do if output remains 0mA on Azbil MagneW FLEX+/PLUS+ MGG10C Media Converter?
- M
  Melissa BrownAug 26, 2025
  If the output remains 0mA on your Azbil Media Converter, verify the power source and power supply voltage, and check the wiring.
I
Ian McconnellAug 23, 2025
What to do if flow rate exceeds the flow range on Azbil Media Converter?
- P
  Philip MackAug 23, 2025
  If the flow rate exceeds the flow range on your Azbil Media Converter, check the flow range setting to ensure it matches the detector and process flow. If it does not, set an appropriate RANGE. Also, verify that the flowmeter has been zeroed; if not, calibrate the flowmeter.