Barco DP2K-36BLP - Installation of the Input Cover

Barco DP2K-36BLP

185 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

12. Removal and installation of the projector covers

Image 12-14

Secure front cover

4. Reinstall the rub ber dus t ring around the lens holder.

12.7 Installation of the input cover

Necessary tools

Flat screwdriver

How to install

1. P lace the top side of the cover on its place.

130

R5906753 DPXK BLP SERIES 20/11/2017

Table of Contents

Default Chapter5
- Table of Contents5
1 Safety9
- General Considerations9
- Important Safety Instructions10
- Product Safety Labels14
- High Brightness Precautions: Hazard Distance (HD)15
- HD for Fully Enclosed Projection Systems17
- HD in Function of Modifying Optics18
2 General19
- Installation Requirements19
- Projector Weight20
- About the Delivered Packages21
- Unpacking the Projector23
- Initial Inspection26
3 Installation Process27
- Installation Process Projector27
- Installation Process Top Cooler27
- Installation Process Stand Alone Cooler28
- Software Upgrade28
- Starting up and Adjusting the System28
4 Physical Installation Projector31
- Positioning the Dpxk BLP Series Projector at Port Window31
- Projector Tilting32
- Access to the Power Connection33
- Power Input Setup of the Dpxk-36BLP34
- Connecting the Dpxk-17/23BLP with the Power Net35
- Connecting the Dpxk-36BLP with the Power Net36
- How to Connect37
- Power Loop through to the Projector Electronics38
- Connecting a UPS to the Projector Electronics38
5 Physical Installation Top Cooler41
- Assembling the Housing41
- Mounting the Housing on the Frame47
- Mounting the Front Support49
- Mount Cooling Frame on the Projector49
- Insert the Cooler Units50
- Mount the Filters52
- Cabling and Tubing53
6 Physical Installation Stand Alone Cooler55
- Supported Mounting Position55
- Assembling the Cooler Housing57
- Mounting the Cooler Housing on the Cooler Frame58
- Preparing the Stand Alone Frame58
- Installing the Brackets on the Cooler Housing59
- Mounting the Cooler Housing on the Frame60
- Insert the Cooler Units62
- Mount the Filters63
- Cabling and Tubing64
- Mount Protection Grid for the LCM Cooler Modules (Option)65
7 Lenses & Lens Holder67
- Available Lenses67
- Lens Selection68
- Lens Installation69
- Lens Removal72
- Lens Shift, Zoom & Focus73
- Back Focal Length Adjustment74
- Scheimpﬂug Adjustment78
- How to Adjust79
- Fixation of the Lens Holder Front Plate81
8 Input & Communication83
- Introduction83
- Local Keypad of the Dpxk-Xxblp84
- Integrated Cinema Processor (ICP)85
- HD-SDI Input Module (Optional)86
- Quad 3G-SDI Input Module (Optional)89
- Integrated Media Block/Server (Optional)93
- Cinema Controller of the Dpxk-Xxblp94
9 Icmp97
- ICMP Introduction97
- Icmp Hdd99
- ICMP Communication Ports100
- ICMP Source Input Ports101
- ICMP Displayport Speciﬁcations102
- ICMP SDI Speciﬁcations104
- ICMP HDMI 2.0 Speciﬁcations107
- ICMP HDMI 1.4 Speciﬁcations109
- ICMP Status Leds111
- ICMP HDD Status Leds112
- ICMP Conﬁguration Via Communicator113
- ICMP Reset113
- Removing a HDD from the ICMP114
- Installing a HDD into the ICMP115
10 Communicator Touch Panel117
- Introduction117
- Installation of the Touch Panel Interface118
11 Starting up121
- Switching on the Dpxk BLP Series Projector121
- Switching off the Dpxk BLP-Series Projector122
12 Removal and Installation of the Projector Covers123
- Removal of the Light Source Cover124
- Removal of the Rear Cover125
- Removal of the Input Cover126
- Removal of the128
- Removal of the Side Cover130
- Installation of the132
- Installation of the Input Cover134
- Installation of the Light Source Cover136
- Installation of the Rear Cover138
- Installation of the Side Cover139
13 Preventative Maintenance Actions141
- Month Maintenance Actions141
14 Maintenance143
- Remove and Clean the Front Dust Filter143
- Remove and Clean both Bottom Dust Filters144
- Check the Cooler Dust Filters145
- Vacuum Cleaning of the Dust Filters146
- Washing and Drying the Dust Filters147
- Cleaning the Lens148
- Cleaning the Exterior of the Projector148
- Check Cooling Liquid Level148
- Cooling Liquid Reﬁll149
- Authorization to Clear Security Warning on the Projector150
15 Convergence153
- Open the Sealed Compartment153
- Close the Sealed Compartment154
- Convergence Controls155
- Red on Blue Convergence156
- Green on Blue Convergence157
16 Color Calibration159
- Calibration Process159
- White Point Calibration159
- Color Gamut Calibration160
17 Pin Conﬁgurations163
- About General Purpose Inputs & Outputs (GPIO)163
- Pin Conﬁgurations of the Communication Ports164
- Ethernet Port165
- Pin Conﬁgurations of the ICMP Communication Ports166
- Pin Conﬁgurations of the Inputs168
18 Speciﬁcations169
- Speciﬁcations of the DP2K-36BLP169
- Speciﬁcations of the DP4K-36BLP170
- Speciﬁcations of the DP2K-23BLP170
- Speciﬁcations of the DP4K-23BLP171
- Speciﬁcations of the DP4K-17BLP172
- Dimensions of the Dpxk-Xxblp173
- Dimensions of the Universal Pedestal174
- Projector Air Inlets and Outlets175
19 Environmental Information177
- Disposal Information177
- China Rohs Compliance177
- Taiwan Rohs Compliance178
- Turkey Rohs Compliance179
- Hazards179
- Production Address180
- Contact Information180
Glossary181
Index183

Related product manuals

Preview: Barco DP2K-12C

Preview: Barco DP2K-19B

Preview: Barco DP2K-23B

Preview: Barco DP2K-20C

Preview: Barco DP2K-20CLP

Barco DP2K-20CLP

Preview: Barco DP2K-10SLP

Barco DP2K-10SLP

Preview: Barco DP2K-E series

Barco DP2K-E series

Preview: Barco DP2K-S Series

Barco DP2K-S Series

Preview: Barco DP2K-C Series

Barco DP2K-C Series

Preview: Barco DP2K SLP Series

Barco DP2K SLP Series