BENSHAW RSi H2 Series - Page 105

Parameter Lists
93
890053-00-02
Code
Name
LCD Display
Setting Range
Initial value
Property*
Ref.
18
Exchange
p.170
19
Up
p.171
20
Down
22
U/D Clear
23
Analog Hold
p.173
24
I-Term Clear
p.220
25
PID Openloop
p.237
26
PID Gain2
p.220
27
PID Ref Change
p.220
28
Pre Excite
p.174
29
Timer In
p.174
31
dis Aux Ref
p.128
32
FWD JOG
p.167
33
REV JOG
p.167
34
Fire Mode
p.175
35
Time Event En
p.176
36
Pre Heat
p.267
37
Damper Open
p.176
38
Pump Clean
p.176
39
Sleep Wake Chg
p.233
40
PID Step Ref L
p.177
41
PID Step Ref M
42
PID Step Ref H
72
8
P8 terminal configuration
P8 Define
Same as P1 - P7
73
9
P9 terminal configuration
P9 Define
Same as P1 - P7
83
DI On Delay Selection
DI On DelayEn
0 0000 0000-1 1111 1111
Δ
p.177
84
DI Off Delay Selection
DI Off DelayEn
0 0000 0000-1 1111 1111
Δ
p.177
85
Multi-function input terminal On filter
DI On Delay
0–10000 (msec)
10
O
p.177
86
Multi-function input terminal Off filter
DI Off Delay
0–10000 (msec)
3
O
p.177
87
Multi-function input terminal selection
DI NC/NO Sel
1 NC (B Type)
0 NO (A Type)
0 0000 0000-1 1111 1111
Δ
p.177
89
Multi-step command delay time
In Check Time
1–5000 (msec)
1
Δ
p.136
90
Multi-function input terminal status
DI Status
1 ON
0 OFF
0 0000 0000-1 1111 1111
O
p.177
91
Pulse input amount display
TI Monitor
0.00-50.00 (kHz)
0.00
X
p.115
92
TI input filter time
TI Filter
0–9999 (msec)
10
O
93
TI minimum input pulse
TI Pls x1
0 - TI Pls x2
0.00
O
94
Output at TI minimum pulse (%)
TI Perc y1
0.00-100.00 (%)
0.00
O
95
TI maximum input pulse
TI Pls x2
TI Pls x1-32.00
32.00
O
96
Output at TI maximum pulse (%)
TI Perc y2
0.00-100.00 (%)
100.00
O
97
TI rotation direction change
TI Inverting
0
No
0
No
O
1
Yes
98
TI quantization level
TI Quantizing
0.00
4
, 0.04-10.00 (%)
0.04
O
[1] 'IN-05' setting range can be changed accordinig to 'IN-06' settings.
[2] IN-12–17 are displayed when IN-06 is set to ‘1 (Bipolar)’.
[3] Quantizing is disabled if ‘0’ is selected.
[4] IN-20 is displayed when the V1/T1 terminal selection switch (SW3) is selected for T1 (PTC Input).
[5] IN-35–47 are displayed when the analog current/voltage input circuit selection switch (SW4) is selected on V2.
[6] IN-50–62 are displayed when the analog current/voltage input circuit selection switch (SW5) is selected on I2.
[7] IN-61 and IN-62 are displayed when IN-60 is set to ‘1 (DI Dependent)’.
[8] IN-72 and IN-73 are available when Extended IO Bd. is installed. Refer to Extended IO option manual for more detailed information.
P9 P8 P7 P6 P5 P4 P3 P2 P1
1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 0
P9 P8 P7 P6 P5 P4 P3 P2 P1
1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 0
P9 P8 P7 P6 P5 P4 P3 P2 P1
1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 0