○○○○○○○○○○○○○○○○○○○○○○
4•14 Reference Guide
○○○○○○○○○○○○○○○○○○○○○○
4•14 Reference Guide
of your error with the following message:
Press ESCAPE to close the user message and
try again, this time selecting the correct destina-
tion.
SAVE GROUP STYLE PERFORMANCE (EXAMPLE)
1. Select GROUP STYLE PERFORMANCE from the
main Save page.
2. Press ENTER to enter the FILE SELECTOR and
select the destination device (Floppy, Hard
disk o SCSI).
3. Select the destination Block then press EN-
TER to gain access.
If necessary, select an empty location to cre-
ate a new Block using the method described
in the Quick Guide, page 1.47.
of your error with the following message:
Press ESCAPE to close the user message and
try again, this time selecting the correct destina-
tion.
SAVE GROUP STYLE PERFORMANCE (EXAMPLE)
1. Select GROUP STYLE PERFORMANCE from the
main Save page.
2. Press ENTER to enter the FILE SELECTOR and
select the destination device (Floppy, Hard
disk o SCSI).
3. Select the destination Block then press EN-
TER to gain access.
If necessary, select an empty location to cre-
ate a new Block using the method described
in the Quick Guide, page 1.47.
○○○○○○○○○○○○○○○○○○○○○○
Performances- Edit Performance 3•23
○○ ○○○○○○○○○○○○○○○○○○○○
Performances- Edit Performance 3•23
Press ENTER to confirm or ESCAPE to cancel
the operation.
Note: This operation does not copy the notes cap-
tured by the sequence. To copy the notes, use the
«Copy events» function (in «Edit Style» or «Edit
Song»).
ERASE TRACK (F8)
This function, available only if you are working
with a Song Performance in Song mode, allows
you to cancel tracks of the current Performance.
In Style/Performance mode, it is not possible to
erase any tracks.
Select the track you wish to cancel. A track en-
gaged by the sequencer cannot be erased.
Press the soft button F8. You are prompted to
confirm with “Are you sure?”:
Press ENTER to confirm or ESCAPE to cancel.
Hint: Cancel Song tracks that are not used. The
resulting Song file will occupy less memory on disk.
Store Performance
Whenever you edit a Performance, you will, at
some point, decide that you either want to save
your new sound combination, or simply forget it
and return to using the instrument as before. A
modified Performance that has not been stored
to memory shows a small mark at the top left hand
corner before the name in the Performance se-
lection window.
If you want to cancel all your modifications, ei-
ther select the same Performance again, or se-
lect another one.
If you decide you want to store your Performance
into the instrument’s memory, the next step will
be to press the STORE PERFORMANCE but-
ton. Any Performance that you create yourself
can be stored in the Global Performances or the
Style Performances banks. During the storing
process, you will first be asked to select a desti-
nation for your new Performance and then given
the opportunity to name it.
SAVING TO THE CURRENT PERFORMANCE
1. Press STORE PERFORMANCE to open the
«Store Performance» dialog window:
2. Press ENTER to save.
To change the name of the Performance,
press the soft button F7 or F8 and change
the name using the keys of the keyboard. You
can refer to the method described in the Al-
phanumeric Entry paragraph on page 1.4 of
the Quick Guide.
Press ENTER to confirm the name and re-
turn to the Store window.
Press ENTER to confirm or ESCAPE to cancel
the operation.
Note: This operation does not copy the notes cap-
tured by the sequence. To copy the notes, use the
«Copy events» function (in «Edit Style» or «Edit
Song»).
ERASE TRACK (F8)
This function, available only if you are working
with a Song Performance in Song mode, allows
you to cancel tracks of the current Performance.
In Style/Performance mode, it is not possible to
erase any tracks.
Select the track you wish to cancel.
A track en-
gaged by the sequencer cannot be erased.
Press the soft button F8. You are prompted to
confirm with “Are you sure?”:
Press ENTER to confirm or ESCAPE to cancel.
Hint: Cancel Song tracks that are not used. The
resulting Song file will occupy less memory on disk.
Store Performance
Whenever you edit a Performance, you will, at
some point, decide that you either want to save
your new sound combination, or simply forget it
and return to using the instrument as before. A
modified Performance that has not been stored
to memory shows a small mark at the top left hand
corner before the name in the Performance se-
lection window.
If you want to cancel all your modifications, ei-
ther select the same Performance again, or se-
lect another one.
If you decide you want to store your Performance
into the instrument’s memory, the next step will
be to press the STORE PERFORMANCE but-
ton. Any Performance that you create yourself
can be stored in the Global Performances or the
Style Performances banks. During the storing
process, you will first be asked to select a desti-
nation for your new Performance and then given
the opportunity to name it.
SAVING TO THE CURRENT PERFORMANCE
1. Press STORE PERFORMANCE to open the
«Store Performance» dialog window:
2. Press ENTER to save.
To change the name of the Performance,
press the soft button F7 or F8 and change
the name using the keys of the keyboard. You
can refer to the method described in the Al-
phanumeric Entry paragraph on page 1.4 of
the Quick Guide.
Press ENTER to confirm the name and re-
turn to the Store window.
To Next Page
Loading...
