GEM SK760 User Manual

○○○○○○○○○○○○○○○○○○○○○○
6•12 Reference Guide
○○○○○○○○○○○○○○○○○○○○○○
6•12 Reference Guide
Effect - To record the changes of the effects as-
signed to the Performance and respective effect
volume levels. These events are captured as
CC16, CC17, CC48, CC49 (see Appendix).
Settings: On, Off.
SELECT ALL TRACKS (F4)
Activates all the tracks for recording and the pa-
rameter changes name to DESELECT ALL
TRACKS. This resets all the tracks in «key-play»
or «seq-play» status.
SOUND VIEW (F5)
Recalls the SOUND VIEW page where you can
see the changes that you may want to make to
the Performance tracks.
TIME/TEMPO (F6)
Recalls the TIME/TEMPO page where you can
program the record/play parameters.
ERASE... (F7)
Cancellation of the track or Song.
Track - Cancels the selected track.
Song - Cancels all the tracks (entire Song) and
leaves an “empty” Song, ready to capture re-
corded events. The Song Performance remains
intact.
METRONOME (F8)
Activates/deactivates the metronome.
LOC
The Song Locator. Indicates the current position
of the Song, expressed in measures, beats and
resolution (tick).
The measure can be modified with the DIAL. It
is not possible to select the next measure after
the Song end point. For example, if the recorded
Song terminates at measure 10, the Locator can-
not be given a value greater than 10 -1 -1.
PLAY/REC MODE
Recording and playback options for the Song.
Linear causes the Song to play or be recorded
once only, from the beginning to the point at which
you press STOP.
Forced Stop causes the song to play or be re-
corded from the specified start locator to the end
locator.
Loop allows you to play or record in a cyclic
manner from the Start point to the End point.
Note: The loop requires an additional memory
buffer. When this mode is selected, the memory
progress bar shows an increased amount of used
memory.
START
Starting indicator. If Loop is active (Play/Rec
Mode= Loop) this parameter indicates the point at
which the Song starts to repeat. The parameter
can be modified with the DIAL.
END
End point marker. If Loop is active (Play/Rec
Mode= Loop) this parameter indicates the point
at which the repeating song ends before looping
back to the Start marker. If the Play/Rec
Mode=Forced Stop, this parameter indicates the
automatic Stop point.
The parameter can be modified with the DIAL.
TIME SIGNATURE
Metro. This parameter can be modified only be-
fore starting a recording. If the Song contains
recorded events, the parameter cannot be modi-
fied.
TEMPO
Initial playing/recording speed. The parameter
can be modified with the DIAL in the «Sound
View» or «Time/Tempo» page, or in the Master
Track.
Tempo changes can be carried out during the
Effect - To record the changes of the effects as-
signed to the Performance and respective effect
volume levels. These events are captured as
CC16, CC17, CC48, CC49 (see Appendix).
Settings: On, Off.
SELECT ALL TRACKS (F4)
Activates all the tracks for recording and the pa-
rameter changes name to DESELECT ALL
TRACKS. This resets all the tracks in «key-play»
or «seq-play» status.
SOUND VIEW (F5)
Recalls the SOUND VIEW page where you can
see the changes that you may want to make to
the Performance tracks.
TIME/TEMPO (F6)
Recalls the TIME/TEMPO page where you can
program the record/play parameters.
ERASE... (F7)
Cancellation of the track or Song.
Track - Cancels the selected track.
Song - Cancels all the tracks (entire Song) and
leaves an “empty” Song, ready to capture re-
corded events. The Song Performance remains
intact.
METRONOME (F8)
Activates/deactivates the metronome.
LOC
The Song Locator. Indicates the current position
of the Song, expressed in measures, beats and
resolution (tick).
The measure can be modified with the DIAL. It
is not possible to select the next measure after
the Song end point. For example, if the recorded
Song terminates at measure 10, the Locator can-
not be given a value greater than 10 -1 -1.
PLAY/REC MODE
Recording and playback options for the Song.
Linear causes the Song to play or be recorded
once only, from the beginning to the point at which
you press STOP.
Forced Stop causes the song to play or be re-
corded from the specified start locator to the end
locator.
Loop allows you to play or record in a cyclic
manner from the Start point to the End point.
Note: The loop requires an additional memory
buffer. When this mode is selected, the memory
progress bar shows an increased amount of used
memory.
START
Starting indicator. If Loop is active (Play/Rec
Mode= Loop) this parameter indicates the point at
which the Song starts to repeat. The parameter
can be modified with the DIAL.
END
End point marker. If Loop is active (Play/Rec
Mode= Loop) this parameter indicates the point
at which the repeating song ends before looping
back to the Start marker. If the Play/Rec
Mode=Forced Stop, this parameter indicates the
automatic Stop point.
The parameter can be modified with the DIAL.
TIME SIGNATURE
Metro. This parameter can be modified only be-
fore starting a recording. If the Song contains
recorded events, the parameter cannot be modi-
fied.
TEMPO
Initial playing/recording speed. The parameter
can be modified with the DIAL in the «Sound
View» or «Time/Tempo» page, or in the Master
Track.
Tempo changes can be carried out during the
○○○○○○○○○○○○○○○○○○○○○○
Edit Sound 2•25
○○○○○○○○○○○○○○○○○○○○○○
Edit Sound 2•25
The maximum segment time is approximately 21
seconds. Assignable values: 0 ... 127.
Level: Sets the Sound level of the segment at
its terminal point. The maximum level corre-
sponds to the volume programmed in the Vol-
ume editor. Assignable values: 0 ... 127.
IMPORTANT
The initial level of the first Key On segment
at the starting point is always zero (it cannot
be modified).
The level at the terminal point of the Key Off
Envelope is always zero (it cannot be modi-
fied).
An illustrated example of how to program Key
On & Key Off Envelopes is shown below.
PROGRAMMING KEY ON AND KEY OFF ENVELOPES
1. To insert a segment, press F6 to open the
SEGMENT selection window and press ENTER
to confirm the ‘Add Segm’ option (shown
selected).
2. Rotate the DIAL to select the envelope seg-
ment that you wish to modify. If necessary,
use the ZOOM option to zoom in on the se-
lected segment.
3. Select the TIME parameter with the down ( )
cursor arrow and rotate the DIAL to set the
required value.
4. Select the LEVEL parameter with the down
( ) cursor arrow and rotate the DIAL to set
the required value.
Edit Sound - Key On Envelope: add 1 segment
Edit Sound - Key On Envelope: modify the Time parameter
Edit Sound - Key On Envelope: select a segment
Edit Sound - Key On Envelope: modify the Level parameter
The maximum segment time is approximately 21
seconds. Assignable values: 0 ... 127.
Level: Sets the Sound level of the segment at
its terminal point. The maximum level corre-
sponds to the volume programmed in the Vol-
ume editor. Assignable values: 0 ... 127.
IMPORTANT
The initial level of the first Key On segment
at the starting point is always zero (it cannot
be modified).
The level at the terminal point of the Key Off
Envelope is always zero (it cannot be modi-
fied).
An illustrated example of how to program Key
On & Key Off Envelopes is shown below.
PROGRAMMING KEY ON AND KEY OFF ENVELOPES
1. To insert a segment, press F6 to open the
SEGMENT selection window and press ENTER
to confirm the ‘Add Segm’ option (shown
selected).
2. Rotate the DIAL to select the envelope seg-
ment that you wish to modify. If necessary,
use the ZOOM option to zoom in on the se-
lected segment.
3. Select the TIME parameter with the down (
)
cursor arrow and rotate the DIAL to set the
required value.
4. Select the LEVEL parameter with the down
(
) cursor arrow and rotate the DIAL to set
the required value.
Edit Sound - Key On Envelope: add 1 segment
Edit Sound - Key On Envelope: modify the Time parameter
Edit Sound - Key On Envelope: select a segment
Edit Sound - Key On Envelope: modify the Level parameter

GEM SK760 Specifications

General

Brand	GEM
Model	SK760
Category	Electronic Keyboard
Language	English