○○○○○○○○○○○○○○○○○○○○○○
2•18 Reference Guide
○○○○○○○○○○○○○○○○○○○○○○
2•18 Reference Guide
Depending on the waveform, values above the
default starting point may cause the sample to
start at a later point, removing some or all of its
attack.
Values below the default value may cause the
sample to start before its normal start point, add-
ing part or all of the samples stored at lower
memory addresses.
WV. START DYN MODE: Selects the mode in
which the Wavestart parameter is linked to key
velocity.
Disable: not linked to key velocity.
Switch: either the entire Wave, or the part of the
Wave following the programmed Wave Start is
read above or below a certain key velocity set-
ting.
Floating: fluctuates the Wave Start according to
the key velocity.
WV. START DYN SNS: With the “Switch” mode
setting, the value (0…127) represents the dy-
namic switch. Above the dynamic switch setting,
the entire Wave is read while below, only the part
of the Wave that follows immediately after the
programmed Wave Start is considered.
Switch assignable values: 0…127
If the mode is “Floating”, the value determines
the distance from the point at which the Wave is
read at the programmed Wave Start, or towards
the end of the Wave. (The Wave is always read
from the Wave start setting, not before). With
positive values, the higher the key velocity, the
nearer the Wave is read at the Wave start set-
ting.
Floating assignable values: –7…+7.
SCALE MODE: Selects a scale (temperament).
Assignable values: 0, 1, 2.
Value 0 corresponds to Equal temperament;
Value 1 corresponds to 1/4 tone difference be-
tween each note;
Value 2 corresponds to a 1/16 tone difference
between each note.
Depending on the waveform, values above the
default starting point may cause the sample to
start at a later point, removing some or all of its
attack.
Values below the default value may cause the
sample to start before its normal start point, add-
ing part or all of the samples stored at lower
memory addresses.
WV. START DYN MODE: Selects the mode in
which the Wavestart parameter is linked to key
velocity.
Disable: not linked to key velocity.
Switch: either the entire Wave, or the part of the
Wave following the programmed Wave Start is
read above or below a certain key velocity set-
ting.
Floating: fluctuates the Wave Start according to
the key velocity.
WV. START DYN SNS: With the “Switch” mode
setting, the value (0…127) represents the dy-
namic switch. Above the dynamic switch setting,
the entire Wave is read while below, only the part
of the Wave that follows immediately after the
programmed Wave Start is considered.
Switch assignable values: 0…127
If the mode is “Floating”, the value determines
the distance from the point at which the Wave is
read at the programmed Wave Start, or towards
the end of the Wave. (The Wave is always read
from the Wave start setting, not before). With
positive values, the higher the key velocity, the
nearer the Wave is read at the Wave start set-
ting.
Floating assignable values: –7…+7.
SCALE MODE: Selects a scale (temperament).
Assignable values: 0, 1, 2.
Value 0 corresponds to Equal temperament;
Value 1 corresponds to 1/4 tone difference be-
tween each note;
Value 2 corresponds to a 1/16 tone difference
between each note.
○○○○○○○○○○○○○○○○○○○○○○
Edit Song 6•19
○○○○○○○○○○○○○○○○○○○○○○
Edit Song 6•19
Copies events from a single track or from all
tracks.
SOFT BUTTONS F3 ... F8
Use the Soft buttons F1...F8 to select the track
from which events will be copied. Depending on
the type of track selected, the following param-
eters may or may not appear.
Track (F3) - Single track. Select the track
with the Soft buttons A...H.
Master track (F4) - The Master Track records
events pertaining to the general controls of
the Song (Tempo, Time Signature, selected
Performance, selected effects).
Chords track (F5) - Track for the chord sym-
bols inserted in the score.
Music track (F6) - Track for the notes of the
score (standard notation).
Lyrics track (F7) - Track for the lyrics of the
score.
All tracks (F8) .
Copy
Copies events from a single track or from all
tracks.
SOFT BUTTONS F3 ... F8
Use the Soft buttons F1...F8 to select the track
from which events will be copied. Depending on
the type of track selected, the following param-
eters may or may not appear.
Track (F3) - Single track. Select the track
with the Soft buttons A...H.
Master track (F4) - The Master Track records
events pertaining to the general controls of
the Song (Tempo, Time Signature, selected
Performance, selected effects).
Chords track (F5) - Track for the chord sym-
bols inserted in the score.
Music track (F6) - Track for the notes of the
score (standard notation).
Lyrics track (F7) - Track for the lyrics of the
score.
All tracks (F8) .
Copy