Keysight N1911A

24 Keysight N1911A/1912A User’s Guide
Figure 3-9 Channel offset display . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 4-1 Bandwidth Filter Shapes . . . . . . . . . . . . . . . . . . . . . . 167
Figure 4-2 E–Series E9320 power sensor default channel setup . . .
168
Figure 4-3 Frequency pop-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Figure 4-4 E-Series E9320 power sensor channel setup when trigger
is selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Figure 4-5 Trace display in dual channel power meter . . . . . . . 174
Figure 4-6 Trace display in single enlarged window . . . . . . . . . 175
Figure 4-7 Trace display with gate control menu . . . . . . . . . . . . 176
Figure 4-8 Trace display with trigger delay menu . . . . . . . . . . . 177
Figure 4-9 Trace display with trace control menu . . . . . . . . . . . 179
Figure 4-10 Trace display in full screen . . . . . . . . . . . . . . . . . . . . 180
Figure 4-11 E-Series E9320 power sensor default channel setup 181
Figure 4-12 Channel offset display . . . . . . . . . . . . . . . . . . . . . . . . 182
Figure 5-1 E9300 E-Series auto-averaging settings . . . . . . . . . 187
Figure 5-2 . . . E9300 E-Series sensor default channel setup 188
Figure 5-3 Frequency pop-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Figure 5-4 Spread spectrum signal . . . . . . . . . . . . . . . . . . . . . . . 192
Figure 5-5 Wideband CDMA error of E-Series E9300 power sensor
versus corrected CW sensor. . . . . . . . . . . . . . . . . 193
Figure 5-6 CDMA (IS-95A): 9Ch Fwd . . . . . . . . . . . . . . . . . . . . . 193
Figure 5-7 Calibration factors versus frequency . . . . . . . . . . . . . 194
Figure 6-1 E-Series CW sensor auto-averaging settings . . . . . . 203
Figure 6-2 E-Series E4410 sensor default channel setup . . . . . 204
Figure 6-3 Frequency pop-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Figure 7-1 8480 Series auto-averaging settings . . . . . . . . . . . . 209
Figure 7-2 8480 Series sensor default channel setup . . . . . . . . 210
Figure 7-3 Reference Calibration Factor pop-up window . . . . . 214
Figure 7-4 Calibration factor pop-up window . . . . . . . . . . . . . . 215
Figure 7-5 Calibration factor display . . . . . . . . . . . . . . . . . . . . . . 215
Figure 7-6 Sensor table selected . . . . . . . . . . . . . . . . . . . . . . . . 218
Figure 7-7 Frequency dependent offset indicator . . . . . . . . . . . 219
Figure 7-8 Frequency/calibration table display . . . . . . . . . . . . . 220
Figure 7-9 “Sensor Tbls” screen . . . . . . . . . . . . . . . . . . . . . . . . . 222
Figure 7-10 “Edit Cal” display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Figure 7-11 Edit table title pop-up . . . . . . . . . . . . . . . . . . . . . . . . 223