Sel SEL-787 - Page 9

viiList of Tables
Date Code 20150130 Instruction Manual SEL-787 Relay
Table 7.3 Protocols Supported on the Various Ports............................................................................ 7.10
Table 7.4 Settings Associated With SNTP...........................................................................................7.13
Table 7.5 Serial Port Automatic Messages ..........................................................................................7.15
Table 7.6 Command Response Header Definitions ............................................................................. 7.17
Table 7.7 Access Commands ............................................................................................................... 7.18
Table 7.8 ANALOG Command ........................................................................................................... 7.19
Table 7.9 ANALOG Command Format............................................................................................... 7.20
Table 7.10 COM Command................................................................................................................... 7.22
Table 7.11 CONTROL Command ......................................................................................................... 7.22
Table 7.12 Three Remote Bit States....................................................................................................... 7.23
Table 7.13 COPY Command.................................................................................................................. 7.23
Table 7.14 COUNTER Command ......................................................................................................... 7.23
Table 7.15 Date Command.....................................................................................................................7.23
Table 7.16 EVENT Command (Event Reports)..................................................................................... 7.24
Table 7.17 EVENT Command Format...................................................................................................7.25
Table 7.18 FILE Command.................................................................................................................... 7.25
Table 7.19 GOOSE Command Variants.................................................................................................7.25
Table 7.20 GROUP Command............................................................................................................... 7.27
Table 7.21 HELP Command .................................................................................................................. 7.28
Table 7.22 HISTORY Command ........................................................................................................... 7.28
Table 7.23 IDENTIFICATION Command............................................................................................. 7.28
Table 7.24 IRI Command....................................................................................................................... 7.29
Table 7.25 LDP Commands................................................................................................................... 7.29
Table 7.26 LDP Command Parameters.................................................................................................. 7.30
Table 7.27 L_D Command (Load Firmware) ........................................................................................ 7.30
Table 7.28 LOO Command.................................................................................................................... 7.30
Table 7.29 Meter Command................................................................................................................... 7.31
Table 7.30 Meter Command Parameters................................................................................................7.31
Table 7.31 Meter Class...........................................................................................................................7.32
Table 7.32 PASSWORD Command.......................................................................................................7.33
Table 7.33 PAS Command Format......................................................................................................... 7.33
Table 7.34 Factory-Default Passwords for Access Levels 1, 2, and C................................................... 7.33
Table 7.35 Valid Password Characters................................................................................................... 7.33
Table 7.36 PUL OUTnnn Command ..................................................................................................... 7.34
Table 7.37 QUIT Command................................................................................................................... 7.35
Table 7.38 R_S Command (Restore Factory Defaults).......................................................................... 7.35
Table 7.39 SER Command (Sequential Events Recorder Report)......................................................... 7.35
Table 7.40 SER Command Format ........................................................................................................7.35
Table 7.41 SER D Command................................................................................................................. 7.36
Table 7.42 SET Command (Change Settings) .......................................................................................7.36
Table 7.43 SET Command Format......................................................................................................... 7.36
Table 7.44 SET Command Editing Keystrokes...................................................................................... 7.37
Table 7.45 SHOW Command (Show/View Settings)............................................................................. 7.37
Table 7.46 SHOW Command Format....................................................................................................7.37
Table 7.47 STATUS Command (Relay Self-Test Status).......................................................................7.40
Table 7.48 STATUS Command Report and Definitions ........................................................................ 7.40
Table 7.49 SUMMARY Command........................................................................................................7.41
Table 7.50 TARGET Command (Display Relay Word Bit Status)
........................................................ 7.42
Table 7.51 TARGET Command Format ................................................................................................ 7.42
Table 7.52 Front-Panel LEDs and the TAR 0 Command....................................................................... 7.42
Table 7.53 TIME Command (View/Change Time)................................................................................7.43
Table 7.54 TRIGGER Command (Trigger Event Report)..................................................................... 7.43
Table 7.55 VEC Command .................................................................................................................... 7.44
Table 8.1 Front-Panel Automatic Messages (FP_AUTO := OVERRIDE) ............................................ 8.3
Table 8.2 Front-Panel Pushbutton Functions ......................................................................................... 8.5
Table 8.3 Possible Warning Conditions (Flashing TRIP LED) ........................................................... 8.13