What to do if Stratasys 3D Printers show 'Model head not initialized'?
The 'Model head not initialized' message on Stratasys 3D printers indicates that head data is not ready. Wait at least 60 seconds after the error is first displayed. If the error persists, open the top cover and unclip the head cable from the model head. Wait a few seconds, then reconnect the head cable to the model head and close the top cover.
How to fix 'Model head removed' error on Stratasys F770?
The 'Model head removed' message on Stratasys 3D printers indicates that the printer lost contact with the model head. Ensure that the head is seated correctly within the gantry. If so, remove the head and then reinstall it.
How to fix 'Model head not communicating' error on Stratasys F770?
The 'Model head not communicating' message on Stratasys 3D printers indicates that the model head is not enabled or communicating. Open the top cover and unclip the head cable from the model head. Wait a few seconds, then reconnect the head cable to the model head and close the top cover.
What to do if Stratasys F770 3D Printers show 'X motor jam'?
If your Stratasys 3D printer displays an 'X motor jam' message, it indicates that the X motor was unable to fully complete a move. Inspect the build chamber for obstructions. If none, open the right head access cover and look for obstructions.
What to do if Stratasys 3D Printers show 'Y motor jam'?
If your Stratasys 3D printer displays a 'Y motor jam' message, it indicates that the Y motor was unable to fully complete a move. Inspect the build chamber for obstructions. If none, open the right head access cover, move the head carnage by hand and look for obstructions.
What to do if Stratasys 3D Printers show 'Loss of vacuum during build'?
If your Stratasys 3D printer displays a 'Loss of vacuum during build' message, it indicates that the build sheet has separated from the platen during build. Ensure the build sheet is installed smooth side down, that no debris is under the build sheet and that the build sheet is completely covering all platen grid lines.
What to do if Stratasys 3D Printers show 'Debris under build sheet'?
Inspect underneath build sheet, particularly around the edges, and remove all debris.
What to do if Stratasys 3D Printers say 'Remove the part'?
The 'Remove the part' message on Stratasys 3D printers indicates that the completed part from the previously built job is still in the printer’s oven chamber. Open the oven door and remove the completed part to clear the message.
How to fix 'Close the door' message on Stratasys F770 3D Printers?
The 'Close the door' message on Stratasys 3D printers indicates that the oven door is open. To resolve this, simply close the oven door.
What to do if Stratasys 3D Printers show insufficient support material?
If your Stratasys 3D printer indicates insufficient support material for a part build, connect a material coil box to the printer that contains a sufficient amount of support material. You can find loading instructions in the manual.
Basic safety tips for printer installation, operation, and maintenance.
Explanation of hazard classifications and product safety symbols used in the guide.
Highlights components and areas of the printer as potential safety hazards.
General safety guidelines to follow when working with the printer.
Details on configuring network settings and setting up Insight/FDM Control Center.
Instructions for replacing the printer's model or support heads.
Steps involved in preparing, selecting, and executing a print job.
Procedures for calibrating the printer's tips.
Explanation of how warnings and errors are displayed and interpreted.
Troubleshooting table listing common issues and their resolutions.
General| Print Technology | Fused Deposition Modeling (FDM) |
|---|---|
| Connectivity | Ethernet, USB |
| Software | GrabCAD Print |
| Build Volume | 1000 x 610 x 610 mm |
| Material Compatibility | ASA |
| Print Speed | Not found |
| Power Requirements | 230 VAC, 50/60 Hz |
To Next Page
