To Next Page
J
Jessica DavisSep 23, 2025
What to do if Stratasys 3D Printers show 'Debris under build sheet'?
- KKristen RamirezSep 23, 2025
Inspect underneath build sheet, particularly around the edges, and remove all debris.
What to do if Stratasys 3D Printers show 'Debris under build sheet'?
Inspect underneath build sheet, particularly around the edges, and remove all debris.
What to do if Stratasys 3D Printers show 'Model head not initialized'?
The 'Model head not initialized' message on Stratasys 3D printers indicates that head data is not ready. Wait at least 60 seconds after the error is first displayed. If the error persists, open the top cover and unclip the head cable from the model head. Wait a few seconds, then reconnect the head cable to the model head and close the top cover.
What to do if Stratasys F770 3D Printers show insufficient model material?
If your Stratasys 3D printer indicates insufficient model material for a part build, connect a material coil box to the printer that contains a sufficient amount of model material. Instructions for loading material can be found in the manual.
What to do if Stratasys 3D Printers show insufficient support material?
If your Stratasys 3D printer indicates insufficient support material for a part build, connect a material coil box to the printer that contains a sufficient amount of support material. You can find loading instructions in the manual.
How to fix 'Close the door' message on Stratasys F770 3D Printers?
The 'Close the door' message on Stratasys 3D printers indicates that the oven door is open. To resolve this, simply close the oven door.
What to do if Stratasys 3D Printers say 'Remove the part'?
The 'Remove the part' message on Stratasys 3D printers indicates that the completed part from the previously built job is still in the printer’s oven chamber. Open the oven door and remove the completed part to clear the message.
What to do if Stratasys F770 shows model material does not match selected job?
If your Stratasys 3D printer displays that the model material does not match the selected job, unload the incorrect model material and load the correct model material for the selected job. Also, unload the incorrect support material and load the correct support material for the selected job.
How to fix 'Close the cover' message on Stratasys F770?
The 'Close the cover' message on Stratasys 3D printers indicates that the top cover is open. Simply close the top cover to resolve this.
How to select a job on Stratasys 3D Printers?
The 'Select a job' message on Stratasys 3D printers indicates that a job has not been selected for building. To resolve this, select the job you’d like to build from the Job Queue.
What to do if Stratasys 3D Printers are busy?
If your Stratasys 3D printer displays a 'Printer busy' message, wait a couple of minutes and then attempt to restart the build.
Basic safety tips for printer installation, operation, and maintenance.
Explanation of hazard classifications and product safety symbols used in the guide.
Highlights components and areas of the printer as potential safety hazards.
General safety guidelines to follow when working with the printer.
Details on configuring network settings and setting up Insight/FDM Control Center.
Instructions for replacing the printer's model or support heads.
Steps involved in preparing, selecting, and executing a print job.
Procedures for calibrating the printer's tips.
Explanation of how warnings and errors are displayed and interpreted.
Troubleshooting table listing common issues and their resolutions.
General| Print Technology | Fused Deposition Modeling (FDM) |
|---|---|
| Connectivity | Ethernet, USB |
| Software | GrabCAD Print |
| Build Volume | 1000 x 610 x 610 mm |
| Material Compatibility | ASA |
| Print Speed | Not found |
| Power Requirements | 230 VAC, 50/60 Hz |
