YASKAWA E-7S SERVOPACK SGD7S - Page 644

17.2 Operation of Digital Operator
17.2.2 Operation of Utility Functions
17-15
17
Appendices
 ACC: Acceleration
Note: Refer to the following section for details on the acceleration rate.
13.3.5 Settings in the Program Table on page 13-13
 DEC: Deceleration
Note: Refer to the following section for details on the deceleration rate.
13.3.5 Settings in the Program Table on page 13-13
 POUT: Programmable Output Signals
Note: Refer to the following section for details on the programmable output signals.
13.3.5 Settings in the Program Table on page 13-13
 EVENT: Pass Condition
Note: Refer to the following section for details on the pass condition and elapsed time.
13.3.5 Settings in the Program Table on page 13-13
㸿㹁㹁㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㸿㹁㹁㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change acceleration
If the value becomes less than 1,
“:” is displayed.
㸿㹁㹁㸮㸮㸮㸻㸯㸱 㸱㸲㸳㸴㸵㸶
㧰㧱㧯㧜㧜㧜㧩㧝㧞㧟㧠㧡㧢㧣㧤
㧰㧱㧯㧜㧜㧜㧩㧝㧞 㧟㧠㧡㧢㧣㧤
Move cursor Change deceleration
㧰㧱㧯㧜㧜㧜㧩㧝㧟 㧟㧠㧡㧢㧣㧤
If the value becomes less than 1,
“:” is displayed.
㹎㹍㹓㹒㸮㸮㸮㸻㹌㸿㹘㸸㹌㸿㹘㸸
㹎㹍㹓㹒㸮㸮㸮㸻㹌㸿㹘㸸㹌㸿㹘㸸
Move cursor Change programmable output signal
Pressing the key changes the display
in the following order.
N → A → Z → :
㹎㹍㹓㹒㸮㸮㸮㸻㹌㹌㹘㸸㹌㸿㹘㸸
Pressing the key changes the display
in the reverse order.
㧱㨂㨀㧜㧜㧜㧩㨀㧝㧞㧟㧠㧡  㧱㨂㨀㧜㧜㧜㧩㨀㧝㧞㧟㧠㧡 
Move cursor
Move cursor

Move cursor
㧱㨂㨀㧜㧜㧜㧩㧵㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧺㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧰㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧜㨀㧝㧞㧟㧠㧡
㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧝㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧣㨀㧝㧞㧟㧠㧡
㧱㨂㨀㧜㧜㧜㧩㧦
Change elapsed time
㧱㨂㨀㧜㧜㧜㧩㨀㧞㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧵㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧵㨀㧞㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧺㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧺㨀㧞㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧰㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧰㨀㧞㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧜㨀㧝㧞㧟㧠㧡
㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧝㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧜㨀㧞㧞㧟㧠㧡
㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧝㨀㧞㧞㧟㧠㧡



㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧣㨀㧝㧞㧟㧠㧡

㧱㨂㨀㧜㧜㧜㧩㧿㧱㧸㧣㨀㧞㧞㧟㧠㧡

Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change pass
condition

Move cursor
Change pass
condition
Move cursor
Change pass
condition
Move cursor
Change pass
condition
Move cursor
Change pass
condition
Change pass
condition
Change pass condition