EasyManuals Logo

D-Link DGS-3100 SERIES Cli Manual

D-Link DGS-3100 SERIES
228 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #53 background imageLoading...
Page #53 background image
DGS-3100 Series Gigabit Stackable Managed Switch CLI Manual
44
create snmp host
Purpose To create a recipient of SNMP traps generated by the Switch’s
SNMP agent.
Syntax
create snmp host <ipaddr> [v1<community_string 20> |
v2c<community_string 20> | v3 [noauth_nopriv | auth_nopriv |
auth_priv]<auth_string 24>]
Description The create snmp host command creates a recipient of SNMP traps
generated by the Switch’s SNMP agent.
Parameters <ipaddr> The IP address of the remote management station to
serve as the SNMP host for the Switch.
v1 – Specifies that SNMP version 1 is to be used. The Simple
Network Management Protocol (SNMP), version 1, is a network
management protocol that provides a means to monitor and control
network devices.
v2c – Specifies that SNMP version 2c is to be used. The SNMP v2c
supports both centralized and distributed network management
strategies. It includes improvements in the Structure of Management
Information (SMI) and adds some security features.
v3 – Specifies that the SNMP version 3 is to be used. SNMP v3
provides secure access to devices through a combination of
authentication and encrypting packets over the network. SNMP v3
adds:
Message integrity ensures that packets have not been
tampered with during transit.
Authentication determines if an SNMP message is from a
valid source.
Encryption scrambles the contents of messages to prevent
it being viewed by an unauthorized source.
<community_string 20> A string of up to 20 alphanumeric
characters that identifies members of an SNMP community. This
string is used like a password to give remote SNMP managers
access to MIB objects in the Switch’s SNMP agent.
noauth_nopriv Specifies that there is no authorization and no
encryption of packets sent between the Switch and a remote SNMP
manager.
auth_nopriv Specifies that authorization is required, but there is no
encryption of packets sent between the Switch and a remote SNMP
manager.
auth_priv Specifies that authorization is required, and that packets
sent between the Switch and a remote SNMP manger are
encrypted.
<auth_string 24> A string of up to 24 alphanumeric characters
used in SNMP v3 to authorize a remote SNMP manager to access
the Switch’s SNMP agent.
Restrictions Only Administrator and oper-level users can issue this command
Example usage:
To create an SNMP host to receive SNMP messages:
DGS3100# create snmp host 10.48.74.100 v3 auth_priv public

Table of Contents

Other manuals for D-Link DGS-3100 SERIES

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the D-Link DGS-3100 SERIES and is the answer not in the manual?

D-Link DGS-3100 SERIES Specifications

General IconGeneral
TypeManaged
LayerLayer 2+
Ports10/100/1000BASE-T
SFP Ports2 or 4 (depends on the model)
Additional SFP PortsNo
VLANsYes
StackingYes, Physical Stacking
QoSYes
Jumbo Frame SupportUp to 9K bytes
ManagementWeb-based
Operating Temperature0°C to 40°C
Humidity10% to 90% non-condensing
Standards ComplianceIEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3x, IEEE 802.1D, IEEE 802.1w, IEEE 802.1s, IEEE 802.1Q, IEEE 802.1p
ModelDGS-3100 SERIES
Storage Temperature-40°C to 70°C

Related product manuals