EasyManuals Logo

ETC Element 2 User Manual

ETC Element 2
693 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #151 background imageLoading...
Page #151 background image
System Basics 137
[About] & [Part] - displays the cue part number for each parameter.
[Expand] &[Effect] - opens the Effect Status Display (Tab 8).
Face Panel
[Shift] & [Escape] - to lock and unlock face panel.
Encoder Paging Keys & [Number] - pages to the desired encoder control page.
[Escape] & Encoder Paging Keys - locks the encoders. Press any encoder page button to
unlock.
[Flexi] & Encoder Paging Key - to invoke flexi encoder states.
[Fader Controls] & [Bump Button] - select a fader page on wings.
[Fader Page] & Rate Wheel - rolls the selected fader page. (Ti/Eos/Gio)
[Fader Page] & [number] - select a fader page on integral faders. (Ti/Eos/Gio)
[Fader Page] - increments the fader page by 1.(Ti/Eos/Gio)
[Shift] & [Fader Page] - decrements the fader page by 1. (Ti/Eos/Gio)
[Learn] & [Load] - opens the selected fader's configuration tools.
[Off] & [Load] - releases control of content, restoring to background and leave cue list
with pending cue in tact.
[Release] & [Load] - releases control of content, restoring to background, and resets cue
list to top.
[Shift] & [Go] or [Shift] & [Back] - cuts the pending cue or the previous cue.
[Shift] & [Load] - to remove content from a fader.
[Shift] & [Stage] - toggles Scroll Lock on and off.
Operations
[At] [Enter] - removes move information from selected channel/parameters.
[At] [At] - set to Level (as defined in Setup).
[Color] (Encoder Paging Key) & Encoder Movement - hold Color Point while adjusting
parameters.
[Copy To] [Copy to] - posts Move To on the command line.
[Full] [Full] - sets selected channels intensity to full and self terminates.
[Label] [Label] - appended to a record target command, clears the current label, this
includes show file labels.
[Recall From] [Recall From] - posts Recall From Cue to the command line.
[Record] [Record] - posts Record Only to the command line.
[Select Active] [Select Active] - Select Active minus submaster contributions.
[Shift] & [Select Active] - posts Select Non-Sub Active.
[Shift] &[Enter] - repeats last command line, unterminated; does a loop of last five
commands.
[Shift] & [At] - recalls last channel(s) and parameters without terminating; does a loop of
last five commands.
[Shift] & [Enter] - reselects the last command and leaves it unterminated; does a loop of
last five commands.
[Shift] & [Block] - posts Intensity Block to the command line.
[Shift] & [Clear] - clears the command line.
[Shift] & [Delay] - posts follow.
[Shift] & Encoder Paging Key - posts the category to the command line. For beam
subcategories, press Image, Form or Shutter twice to post Beam. (Ion/Gio)
[Shift] & Encoder Movement - accesses fine mode.
[Shift] & Encoder Push/ Toggle - posts the parameter to the command line. (Ion)
[Shift] & Gel Tile - cycles through three modes of Brightness.
[Shift] & [Full] or [Shift] & [Out] - flash on or flash out.
[Shift] & [+] or [Shift] & [-] - +% or -%.

Table of Contents

Other manuals for ETC Element 2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ETC Element 2 and is the answer not in the manual?

ETC Element 2 Specifications

General IconGeneral
DMX Outputs2
TouchscreenYes
NetworkingEthernet
TypeLighting Control Console
Master Faders2
Encoders4
Ethernet Ports2
USB Ports4
Video OutputDisplayPort
Power Input100-240VAC, 50/60Hz
Power SupplyInternal
Control Channels6144
OutputArt-Net
DisplayMulti-Touch LCD
StorageSolid State Drive (SSD)

Related product manuals